AUDIO AND VISUAL SYSTEM (w/ Multi-display) DTC CHECK / CLEAR


  1. CHECK DTC (CHECK USING INTELLIGENT TESTER)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / DTC.

    5. Check for DTCs, and then write them down.

    6. Check the details of the DTC(s) Click here.

  2. CLEAR DTC (CLEAR USING INTELLIGENT TESTER)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / DTC.

    5. Clear the DTCs.

  3. START DIAGNOSTIC MODE

    Tech Tips


    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    • If the system cannot enter diagnostic mode, inspect all AVC-LAN communication components and repair or replace malfunctioning parts Click here.

    • Start diagnostic mode 15 seconds after turning the engine switch on (IG). Otherwise, some items cannot be checked.


    1. Start the engine.

    2. While pressing and holding the "MENU" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

    3. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

  4. FAILURE DIAGNOSIS


    1. A019MRP

      The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.

  5. SYSTEM CHECK


    1. A019NP5

      The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.

  6. CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

    Tech Tips

    When "NCON" is displayed for all devices connected using the AVC-LAN, or when all device names are not displayed, check if there is a short circuit in the AVC-LAN or devices connected to the AVC-LAN. Repair or replace parts as necessary Click here.


    1. A019N6DE01

      System check mode screen description

      Screen Description
      Display Content
      *a: Device Name List No. 1

      • Device Name List No. 1 displays some of the devices that make up the audio and visual system.

      • The names of the components from Device Name List No. 1 are shown in the following table.
      *b: Check Result Result codes for all devices are displayed.
      *c: Memory Clear

      • Present and history DTCs and registered connected device names are cleared.

      • Press the "Memory CLR" switch for 3 seconds.
      *d: Recheck

      • A system check will be performed again after the memory is cleared.

      • The "Recheck" switch will dim during a system check.
      *e: Device Name List No. 2

      • Device Name List No. 2 displays some of the devices that make up the audio and visual system.

      • The names of the components from Device Name List No. 2 are shown in the following table.
      *a: Device Name List No. 1 Description
      Name Component Connection Method
      DA Radio receiver assembly -
      DSP-AMP Stereo component amplifier assembly Communication line for AVC-LAN
      DISP Multi-display assembly Communication line for AVC-LAN
      R-TOUCH Remote operation board Communication line for AVC-LAN
      *b: Check Result Description
      Result Meaning Action
      OK The device does not respond with a DTC. -
      DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode".
      NCON The device was previously present, but does not respond in diagnostic mode.

      - Check power supply wire harness of the device.

      - Check the AVC-LAN of the device.
      NRES The device responds in diagnostic mode, but gives no DTC information.

      - Check power supply wire harness of the device.

      - Check the AVC-LAN of the device.
      *e: Device Name List No. 2 Description
      Name Component Connection Method
      AUX No. 1 stereo jack adapter assembly Vehicle wire harness
    2. A019MEDE01

      Unit check mode screen description

      Screen Description
      Display Content
      *a: Device name Target device
      *b: History DTC Diagnostic memory results and stored DTCs are displayed.
      *c: Current DTC DTCs output in the service check are displayed.
      *d: DTC DTC (Diagnostic Trouble Code)
      *e: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (Both response to diagnostic system check result and the displayed data are cleared.).

      Tech Tips


      • This screen is updated once per second.

      • A maximum of 6 DTCs can be displayed for history and present DTCs.

    3. A019K6G
      A019NRA

      Read the system check result.


      1. If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

        Note

        A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.

        Tech Tips


        • When all results are "OK", this means that no DTCs are present.

        • When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

      2. Check the details of the DTC(s) Click here.

  7. DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


    1. A019O2Y

      Clear DTCs


      1. Press the "Memory CLR" switch for 3 seconds.

      2. Confirm that the check results are cleared.

        Tech Tips


        • To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

        • When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

    2. A019N7W

      Recheck


      1. Press the "Recheck" switch.

      2. A019OHV

        Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

        Tech Tips

        When DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

  8. FINISH DIAGNOSTIC MODE


    1. Turn the engine switch off.