POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM FREEZE FRAME DATA


  1. FREEZE FRAME DATA

    Note


    • Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.

    • Turn the engine switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.


    1. Turn the engine switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the intelligent tester on.

    5. Check the freeze frame data. Enter the following menus: Chassis / Tilt & Telescopic / DTC.

      Tilt & Telescopic
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tilt Position

      Current tilt position data/

      Min.: 0

      Max.: 65535

      28672 to 36864 -
      Telesco Position

      Current telescopic position data/

      Min.: 0

      Max.: 65535

      28672 to 36864 -
      Tilt Return Position

      Memorized tilt return position data/

      Min.: 0

      Max.: 65535

      28672 to 36864 -
      Telesco Return Position

      Memorized telescopic return position data/

      Min.: 0

      Max.: 65535

      28672 to 36864 -
      Tilt Up Switch

      Input state of tilt up by manual switch/

      ON or OFF

      ON: Tilt up activated by manual switch

      OFF: Tilt up not activated by manual switch

      -
      Tilt Up SW(CAN)

      Input state of tilt up by manual switch/

      ON or OFF

      ON: Tilt up activated by manual switch

      OFF: Tilt up not activated by manual switch

      -
      Tilt Down Switch

      Input state of tilt down by manual switch/

      ON or OFF

      ON: Tilt down activated by manual switch

      OFF: Tilt down not activated by manual switch

      -
      Tilt Down SW(CAN)

      Input state of tilt down by manual switch/

      ON or OFF

      ON: Tilt down activated by manual switch

      OFF: Tilt down not activated by manual switch

      -
      Telesco Short Switch

      Input state of telescopic short by manual switch/

      ON or OFF

      ON: Telescopic short activated by manual switch

      OFF: Telescopic short not activated by manual switch

      -
      Telesco Short SW(CAN)

      Input state of telescopic short by manual switch/

      ON or OFF

      ON: Telescopic short activated by manual switch

      OFF: Telescopic short not activated by manual switch

      -
      Telesco Long Switch

      Input state of telescopic long by manual switch/

      ON or OFF

      ON: Telescopic long activated by manual switch

      OFF: Telescopic long not activated by manual switch

      -
      Telesco Long SW(CAN)

      Input state of telescopic long by manual switch/

      ON or OFF

      ON: Telescopic long activated by manual switch

      OFF: Telescopic long not activated by manual switch

      -
      T&T Manual SW Data

      Voltage data of manual switch/

      Min.: 0.00 V

      Max.: 4.99 V

      Neutral position: Below 0.2 V

      Tilt up: 1.67 to 2.13 V

      Tilt down: 0.54 to 0.74 V

      Telescopic contract: 1.08 to 1.40 V

      Telescopic extend: 2.22 to 2.77 V

      -
      Power Source Voltage

      Voltage data of power supply/

      Min.: 0.00 V

      Max.: 19.99 V

      11 to 14 V -
      Freeze Speed Info

      Vehicle speed data/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      Actual vehicle speed -
      IG Switch (CAN)

      Communication state of engine switch/

      ON or OFF

      ON: Communication normal

      OFF: Communication interrupted

      -
      IG Switch

      Input state of engine switch/

      ON or OFF

      ON: Input signal normal

      OFF: Input signal interrupted

      -
      Receive from Meter

      Communication state of combination meter signal/

      OK or Interpt

      OK: Communication normal

      Interpt: Communication interrupted

      -
      Receive from Seat ECU

      Communication state of position control ECU signal/

      OK or Interpt

      OK: Communication normal

      Interpt: Communication interrupted

      -
      Receive from Combi

      Communication state of combination switch ECU signal/

      OK or Interpt

      OK: Communication normal

      Interpt: Communication interrupted

      -
      J/B

      Communication state of main body ECU signal/

      OK or Interpt

      OK: Communication normal

      Interpt: Communication interrupted

      -
      Handle Position

      Steering wheel position signal/

      Away or Return

      Away: Steering wheel in away position

      Return: Steering wheel in return position

      (Except remote start)

      -
      The Number of DTCs

      Number of stored DTCs/

      Min.: 0

      Max.: 255

      Actual number of stored DTCs -