YAW RATE AND ACCELERATION SENSOR INSTALLATION


  1. INSTALL YAW RATE AND ACCELERATION SENSOR


    1. A019NMDE02

      Connect the connector to the yaw rate and acceleration sensor.

      Note

      Make sure that the yaw rate and acceleration sensor connector is connected securely.

    2. Install the yaw rate and acceleration sensor with the 2 bolts.

      Torque:
      15 N*m  { 147 kgf*cm, 11 ft.*lbf }

      Note


      • Be sure to insert the yaw rate and acceleration sensor claw into the stopper hole while installing the yaw rate and acceleration sensor.

      • Do not damage the yaw rate and acceleration sensor.

      • Make sure that the yaw rate and acceleration sensor is installed securely.

      • Do not use dropped or damaged parts.

      • Keep the contact surfaces of the yaw rate and acceleration sensor and the body free of foreign matter.

      • Make sure that the sensor is facing the correct direction.

  2. INSTALL CONSOLE BOX (for LHD)


    1. A019MGBE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 3 clips.

    4. Install the console box with the 5 screws <D>.

  3. INSTALL CONSOLE BOX (for RHD)


    1. A019MQ4E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 2 clips.

    4. Install the console box with the 5 screws <D>.

  4. INSTALL FRONT CONSOLE BOX COVER


    1. A019M0N

      Connect the connector.

    2. Engage the 5 guides and 2 clips, and install the front console box cover.

  5. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019KVZ

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  6. INSTALL INSTRUMENT PANEL FINISH PANEL


    1. A019MX7

      Engage the 2 guides, claw and 2 clips to install the instrument panel finish panel as shown in the illustration.

  7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. Engage the 8 clips and 2 guides.

    3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.

    4. A019NKJ

      Engage the 2 claws to close the cover as shown in the illustration.

  8. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. A019N7C

      Engage the 4 claws and 2 guides to install the No. 1 switch hole base.

  9. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A019L27

      Engage the 2 clips to install the cowl side trim sub-assembly LH.

    2. Install the clip.

  10. INSTALL INSTRUMENT PANEL GARNISH LH


    1. A019K28

      Engage the 6 clips to install the instrument panel garnish LH.

  11. INSTALL FRONT DOOR SCUFF PLATE LH


    1. w/ Illumination:


      1. Connect the connector.

    2. A019LA0

      Engage the 4 clips, guide and 7 claws, and install the front door scuff plate LH.

  12. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION

    Click here