REAR SPEED SENSOR (for AWD) INSTALLATION

Tech Tips

If the sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.


  1. INSTALL REAR SPEED SENSOR LH


    1. A019LIWE02
      Text in Illustration
      *1 No. 1 Bracket
      *2 Bolt A
      *3 Bolt B

      Install the No. 1 bracket and rear speed sensor to the rear trailing arm assembly and the rear axle carrier sub-assembly with the 2 bolts.

      Torque:
      Bolt A
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Bolt B
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note


      • Prevent foreign matter from attaching to the rear speed sensor tip.

      • Clean the speed sensor installation hole and the contact surfaces every time the rear speed sensor is removed.

    2. A019LWVE01
      Text in Illustration
      *1 No. 2 Bracket
      *2 No. 3 Bracket

      Install the No. 3 bracket and No. 2 bracket to the upper control arm with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. A019K9TE01
      Text in Illustration
      *1 No. 4 Bracket

      Install the No. 4 bracket to the rear member assembly with the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }
    4. A019KDFE01
      Text in Illustration
      *1 No. 4 Bracket

      Connect the rear speed sensor connector.

  2. INSTALL REAR SPEED SENSOR RH


    1. A019O34E02
      Text in Illustration
      *1 No. 1 Bracket
      *2 Bolt A
      *3 Bolt B

      Install the No. 1 bracket and rear speed sensor to the rear trailing arm assembly and the rear axle carrier sub-assembly with the 2 bolts.

      Torque:
      Bolt A
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Bolt B
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note


      • Prevent foreign matter from attaching to the rear speed sensor tip.

      • Clean the speed sensor installation hole and the contact surfaces every time the rear speed sensor is removed.

    2. A019L9PE01
      Text in Illustration
      *1 No. 2 Bracket
      *2 No. 3 Bracket

      Install the No. 3 bracket and No. 2 bracket to the upper control arm with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. A019K18E01
      Text in Illustration
      *1 No. 4 Bracket

      Install the No. 4 bracket to the rear member assembly with the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }
    4. A019P7KE01

      Connect the rear speed sensor connector.

  3. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. CHECK FOR SPEED SENSOR SIGNAL

    Tech Tips

    Click here.