DIFFERENTIAL OIL SEAL REPLACEMENT


  1. DRAIN AUTOMATIC TRANSAXLE FLUID


    1. Remove the 2 bolts, clip and front fender apron seal LH.

    2. A019N41

      Remove the refill plug and gasket from the automatic transaxle.

    3. A019NDI

      Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle.

    4. A019OZ6E02
      Text in Illustration
      *1 No. 1 Transmission Oil Filler Tube

      Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle.

    5. Drain the ATF from the automatic transaxle.

    6. A019OZ6E02
      Text in Illustration
      *1 No. 1 Transmission Oil Filler Tube

      Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube into the automatic transaxle.

      Torque:
      0.8 N*m  { 8 kgf*cm, 7 in.*lbf }
    7. A019NDI

      Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug into the automatic transaxle.

      Tech Tips

      Reuse the old gasket. The overflow plug will be removed again to adjust the fluid level.

    8. A019N41

      Temporarily install the gasket and refill plug into the automatic transaxle.

      Tech Tips

      Reuse the old gasket. The refill plug will be removed again to adjust the fluid level.

  2. REMOVE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  3. REMOVE DRIVE SHAFT BEARING BRACKET


    1. A019MZA

      Remove the 3 bolts and drive shaft bearing bracket.

  4. REMOVE TRANSAXLE CASE OIL SEAL


    1. A019NGME02

      Using SST, tap out the transaxle case oil seal.

      SST
      09308-00010

  5. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    1. A019NJXE02

      Using SST, tap out the front transaxle case oil seal.

      SST
      09308-00010

  6. INSTALL TRANSAXLE CASE OIL SEAL


    1. A019KAKE02

      Coat the lip of a new transaxle case oil seal with a small amount of MP grease.

    2. Using SST and a hammer, tap in the transaxle case oil seal.

      SST
      09316-10010
      09950-70010   ( 09951-07100 )
      Oil seal tap in depth
      -0.5 to 0.5 mm (-0.0197 to 0.0196 in.)

      Note

      Check that the oil seal is installed in the correct direction.

  7. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    1. A019OIUE02

      Coat the lip of a new front transaxle case oil seal with a small amount of MP grease.

    2. Using SST and a hammer, tap in the front transaxle case oil seal.

      SST
      09316-60011   ( 09316-00011 )
      Oil seal tap in depth
      -0.5 to 0.5 mm (-0.0197 to 0.0196 in.)

      Note

      Check that the oil seal is installed in the correct direction.

  8. INSTALL DRIVE SHAFT BEARING BRACKET


    1. A019MZA

      Install the drive shaft bearing bracket with the 3 bolts.

      Torque:
      64 N*m  { 649 kgf*cm, 47 ft.*lbf }

  9. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  10. ADD AUTOMATIC TRANSAXLE FLUID

    Click here

  11. INSPECT AUTOMATIC TRANSAXLE FLUID LEAK

  12. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  13. CHECK ABS SPEED SENSOR SIGNAL

    Click here