SHIFT LEVER REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A019LPB

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  4. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A019OY8

      Move the shift lever to N.

    2. Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 4 claws and 4 clips.

    3. w/o Seat Heater System:


      1. Disconnect the connector from the console box hole cover.

    4. w/ Seat Heater System:


      1. A019OCZ

        Disengage the 6 claws.

      2. Disconnect the connector and remove the seat heater switch with console box hole cover.

    5. A019K0Q

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 3 claws and 3 clips.

    6. Disconnect each connector.

    7. Disengage the clamp and remove the upper console panel sub-assembly.

  5. REMOVE NO. 2 CONSOLE BOX DUCT


    1. A019N18

      Disconnect each connector and disengage the 2 clamps.

    2. A019KD8

      Remove the 2 screws and the No. 2 console box duct.

  6. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY


    1. A019OL2

      w/o Rear Seat Entertainment System:


      1. Disengage the 5 claws and 6 clips, and remove the console rear end panel sub-assembly.

    2. w/ Rear Seat Entertainment System:


      1. Disengage the 5 claws and 6 clips.

      2. Disconnect each connector and remove the console rear end panel sub-assembly.

  7. REMOVE REAR CONSOLE BOX ASSEMBLY


    1. A019LRAE01
      Text in Illustration
      *1 Screw
      *2 Bolt

      Remove the 2 screws and 4 bolts.

    2. A019PIBE01

      Pull the rear console box assembly in the direction indicated by the arrow (1) to disengage the 8 guides and remove the rear console box assembly as shown in the illustration.

      Note

      Make sure to remove the rear console box assembly in the direction indicated by the arrow (2). Failure to do so will damage the console box and front seat.

  8. REMOVE INSTRUMENT PANEL GARNISH LH


    1. A019MAJ

      Using moulding remover B, disengage the 6 clips and remove the instrument panel garnish LH as shown in the illustration.

  9. REMOVE NO. 1 SWITCH HOLE BASE


    1. A019JWR

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A019N7Y

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A019KVT

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  11. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A019PC7

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  12. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019MQD

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  13. REMOVE FRONT CONSOLE BOX COVER


    1. A019P7H

      Using moulding remover A, disengage the 2 clips and 5 guides.

    2. Disconnect the connector and remove the front console box cover.

  14. REMOVE CONSOLE BOX (for LHD)


    1. A019KOZ

      Remove the 5 screws <D>.

    2. A019OKHE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 3 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  15. REMOVE CONSOLE BOX (for RHD)


    1. A019NGF

      Remove the 5 screws <D>.

    2. A019KN6E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 2 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  16. REMOVE SHIFT LEVER ASSEMBLY


    1. Move the shift lever to N.

    2. A019NSH

      Disconnect the shift lock control ECU connector and transmission control switch wire connector.

    3. Disconnect the 3 clamps.

    4. Remove the 4 nuts and shift lever assembly.

    5. A019JV3

      Disconnect the end of the transmission control cable assembly from the shift lever assembly.

    6. Turn the lock nut counterclockwise. While holding the lock nut, disconnect the transmission control cable from the shift lever retainer.