PARK / NEUTRAL POSITION SWITCH INSTALLATION


  1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Move the shift lever to N.

    2. A019MIUE09
      Text in Illustration
      *a Protrusion

      Align the protrusions of the park/neutral position switch.

    3. Install the park/neutral position switch to the control shaft with the 2 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Note


      • Before installing the park/neutral position switch, remove any dirt or rust on the installation portion of the control shaft. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.

      • After installing the park/neutral position switch, confirm that the 2 protrusions on the switch are aligned.

    4. Install the control shaft lever to the control shaft with the nut and washer.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    5. Connect the connector to the park/neutral position switch.

  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Install a new clip to the control cable bracket.

    2. A019MFEE04
      Text in Illustration
      *1 Control Cable
      *a Claw A
      *b Claw B

      Install the control cable to the control cable bracket.

      Note


      • Make sure that the claws A on the clip are securely fit into the bracket holes.

      • Make sure that the cable is securely installed inside of the claws B of the clip.

    3. A019OKV

      Connect the transmission control cable to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note

      Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.

  3. INSTALL AIR CLEANER ASSEMBLY


    1. A019KVSE01
      Text in Illustration
      *a A side view
      *b Front of the vehicle
      *c 11 to 14 mm (0.433 to 0.551 in.)

      Install the air cleaner hose with the hose clamp.

      Note

      Install the air cleaner hose clamp so that the orientation is as shown in the illustration.

    2. A019M7QE02
      Text in Illustration
      *a Tab
      *b Hole

      Insert the tab of the air cleaner assembly to the hole of the vehicle body as shown in the illustration.

    3. Install the air cleaner assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    4. A019LTQE02
      Text in Illustration
      *a Light blue paint mark

      Connect the vacuum hose to the 2 clamps of the air cleaner hose.

      Note

      Align the light blue paint mark of the vacuum hose with the clamp of the air cleaner hose.

    5. Connect the vacuum hose.

    6. Connect the ventilation hose to the cylinder head cover.

    7. Connect the vacuum switching valve connector and install the vacuum hose to the 2 clamps.

    8. Connect the No. 2 fuel vapor feed hose to the vacuum switching valve and clamp of the air cleaner hose.

    9. Connect the mass air flow meter connector and install the wire harness clamp to the air cleaner assembly.

    10. Connect the vacuum switching valve connector and install the wire harness clamp to the air cleaner assembly.

  4. INSTALL INLET NO. 1 AIR CLEANER


    1. A019LTK

      Install the No. 1 air cleaner inlet with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL INLET NO. 2 AIR CLEANER


    1. A019ODB

      Install the No. 2 air cleaner inlet with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  6. INSTALL BATTERY


    1. Install the battery and battery tray.

    2. A019LTJ

      Install the battery clamp with the bolt and nut.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the positive (+) cable to the positive (+) battery terminal.

      Torque:
      6.4 N*m  { 65 kgf*cm, 57 in.*lbf }

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY


    1. A019KNK

      Fit the 3 retainers and install the No. 1 engine cover sub-assembly.

  9. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    1. A019OCLE01

      Install the outer cowl top panel sub-assembly with the 4 bolts, 4 nuts*1 and 2 nuts*2.

      Torque:
      Nut*1
      85 N*m  { 867 kgf*cm, 63 ft.*lbf }
      Nut*2
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Bolt
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A019O7N

      Engage the grommet and clamp to install the wire harness.

    3. Connect the connector (w/ Windshield Deicer).

  10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    1. A019OF3E01

      Install the outer cowl top panel sub-assembly with the 4 bolts, 4 nuts*1 and 2 nuts*2.

      Torque:
      Nut*1
      85 N*m  { 867 kgf*cm, 63 ft.*lbf }
      Nut*2
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Bolt
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A019N0P

      Engage the grommet and clamp to install the wire harness.

    3. Connect the connector (w/ Windshield Deicer).

  11. INSTALL HOSE BRACKET (for LHD)


    1. A019P7C

      Install the hose bracket to the outer cowl top panel sub-assembly with the 2 nuts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  12. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  13. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION


    1. Apply the parking brake.

    2. Turn the engine switch on (IG).

    3. Depress the brake pedal and check that the engine starts when the shift lever is in N or P, but does not start in any other position.

    4. Check that the back-up light comes on when the shift lever is moved to R, but the light does not come on in any other position. If the operation cannot be done as specified, check the park/neutral position switch for continuity.

  14. INSPECT SHIFT LEVER POSITION


    1. When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Start the engine and make sure that the vehicle moves forward when moving the shift lever from N to D and moves rearward when moving the shift lever to R.

      If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.

  15. ADJUST SHIFT LEVER POSITION


    1. Apply the parking brake and move the shift lever to N.

    2. Remove the console box Click here.

    3. A019NSH

      Disconnect the shift lock control ECU connector and transmission control switch wire connector.

    4. Disconnect the 3 clamps.

    5. Remove the 4 nuts and shift lever assembly.

    6. A019JV3

      Disconnect the end of the transmission control cable assembly from the shift lever assembly.

    7. Turn the lock nut counterclockwise. While holding the lock nut, disconnect the transmission control cable from the shift lever retainer.

    8. A019KDKE02
      Text in Illustration
      *1 Slide
      *2 Slider
      *3 Lock Piece
      *a Pull

      Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

    9. A019OI9E03
      Text in Illustration
      *1 Lock Nut
      *2 Stopper
      *a Push in

      Turn the lock nut of the transmission control cable counterclockwise. While holding the lock nut, push in the stopper.

    10. Connect the outer part of the transmission control cable to the shift lever retainer.

      A019P12E02
      Text in Illustration
      *1 Shift Lever Retainer *2 Stopper
      *3 Lock Nut - -

      Note

      The lock nut is fully seated against the shift lever retainer.

    11. A019JOJE01
      Text in Illustration
      *1 Lock Piece

      Install the transmission control cable end to the shift lever assembly.

      Note


      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    12. A019NSH

      Install the shift lever assembly with the 4 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    13. Connect the 3 clamps to the shift lever assembly.

    14. Connect the 2 connectors.

    15. A019OQN

      Push the lock piece into the adjuster case.

      Note


      • Check that the park/neutral position switch and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

    16. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

    17. Install the console box Click here.