PARK / NEUTRAL POSITION SWITCH INSTALLATION


  1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Move the shift lever to N.

    2. A019MIUE06
      Text in Illustration
      *1 Protrusion

      Align the protrusions of the park/neutral position switch.

    3. A019N6Z

      Install the park/neutral position switch to the control shaft with the 2 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Note


      • Before installing the park/neutral position switch, remove any dirt or rust on the installation portion of the control shaft. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.

      • After installing the park/neutral position switch, confirm that the 2 protrusions on the switch are aligned.

    4. A019MIW

      Install the control shaft lever to the control shaft with the nut and washer.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    5. Connect the connector to the park/neutral position switch.

  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Install a new clip to the control cable bracket.

    2. A019MFEE03
      Text in Illustration
      *1 Claw A
      *2 Claw B
      *3 Control Cable

      Install the control cable to the control cable bracket.

      Note


      • Make sure that the claws A on the clip are securely fit into the bracket holes.

      • Make sure that the cable is securely installed inside of the claws B of the clip.

    3. A019OKV

      Connect the transmission control cable to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note

      Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.

  3. INSTALL AIR CLEANER ASSEMBLY


    1. A019M7QE01
      Text in Illustration
      *1 Tab
      *2 Hole

      Insert the tab of the air cleaner assembly to the hole of the vehicle body as shown in the illustration.

    2. A019JQO

      Install the air cleaner assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. A019L8LE01
      Text in Illustration
      *1 Ventilation Hose
      *2 Fuel Vapor Feed Hose

      Connect the air cleaner hose to the throttle body with the hose clamp.

    4. Connect the ventilation hose and the fuel vapor feed hose.

    5. A019LU3

      Connect the 2 vacuum hoses.

    6. A019KSB

      Connect the 2 wire harness clamps and vacuum switching valve connector.

    7. A019LPG

      Connect the vacuum hose to the intake air surge tank assembly.

    8. Install the hose to the hose clamp.

    9. A019K7G

      Connect the mass air flow meter connector and wire harness clamp.

  4. INSTALL INLET NO. 1 AIR CLEANER


    1. A019ND6

      Install the No. 1 air cleaner inlet with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the vacuum hose clamp to the No. 1 air cleaner inlet.

  5. INSTALL INLET NO. 2 AIR CLEANER


    1. A019O60

      Install the No. 2 air cleaner inlet with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the 2 vacuum hose clamps to the No. 2 air cleaner inlet.

  6. INSTALL BATTERY


    1. Install the battery and battery tray.

    2. A019LTJ

      Install the battery clamp with the bolt and nut.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the positive (+) cable to the positive (+) battery terminal.

      Torque:
      6.4 N*m  { 65 kgf*cm, 57 in.*lbf }

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. INSTALL V-BANK COVER SUB-ASSEMBLY


    1. A019LVN

      Fit the 4 retainers and install the V-bank cover sub-assembly.

  9. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    1. A019OCLE01

      Install the outer cowl top panel sub-assembly with the 4 bolts, 4 nuts*1 and 2 nuts*2.

      Torque:
      Nut*1
      85 N*m  { 867 kgf*cm, 63 ft.*lbf }
      Nut*2
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Bolt
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A019O7N

      Engage the grommet and clamp to install the wire harness.

    3. Connect the connector (w/ Windshield Deicer).

  10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    1. A019OF3E01

      Install the outer cowl top panel sub-assembly with the 4 bolts, 4 nuts*1 and 2 nuts*2.

      Torque:
      Nut*1
      85 N*m  { 867 kgf*cm, 63 ft.*lbf }
      Nut*2
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Bolt
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A019N0P

      Engage the grommet and clamp to install the wire harness.

    3. Connect the connector (w/ Windshield Deicer).

  11. INSTALL FRONT SHOCK ABSORBER CAP (w/ Air Suspension)


    1. A019N7O

      Install the front shock absorber cap with the 3 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

  12. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Tech Tips

    See the steps from "Install Windshield Wiper Motor and Link Assembly" through "Install Engine Room Side Cover LH" Click here.

  13. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION


    1. Apply the parking brake.

    2. Turn the engine switch on (IG).

    3. Depress the brake pedal and check that the engine starts when the shift lever is in N or P, but does not start in any other position.

    4. Check that the back-up light comes on when the shift lever is moved to R, but the light does not operate in any other position. If the operation cannot be done as specified, check the park/neutral position switch for continuity.

  14. INSPECT SHIFT LEVER POSITION


    1. When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Start the engine and make sure that the vehicle moves forward when moving the shift lever from N to D and moves rearward when moving the shift lever to R.

      If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.

  15. ADJUST SHIFT LEVER POSITION


    1. Apply the parking brake and move the shift lever to N.

    2. Remove the console box Click here.

    3. A019NSH

      Disconnect the shift lock control ECU connector and transmission control switch wire connector.

    4. Disconnect the 3 clamps.

    5. Remove the 4 nuts and shift lever assembly.

    6. A019JV3

      Disconnect the end of the transmission control cable assembly from the shift lever assembly.

    7. Turn the lock nut counterclockwise. While holding the lock nut, disconnect the transmission control cable from the shift lever retainer.

    8. A019KDKE01
      Text in Illustration
      *1 Slide
      *2 Pull
      *3 Slider
      *4 Lock Piece

      Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

    9. A019OI9E02
      Text in Illustration
      *1 Lock Nut
      *2 Push in
      *3 Stopper

      Turn the lock nut of the transmission control cable counterclockwise. While holding the lock nut, push in the stopper.

    10. Connect the outer part of the transmission control cable to the shift lever retainer.

      A019P12E02
      Text in Illustration
      *1 Shift Lever Retainer *2 Stopper
      *3 Lock Nut - -

      Note

      The lock nut is fully seated against the shift lever retainer.

    11. A019JOJE01
      Text in Illustration
      *1 Lock Piece

      Install the transmission control cable end to the shift lever assembly.

      Note


      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    12. A019NSH

      Install the shift lever assembly with the 4 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    13. Connect the 3 clamps to the shift lever assembly.

    14. Connect the 2 connectors.

    15. A019OQN

      Push the lock piece into the adjuster case.

      Note


      • Check that the park/neutral position switch and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

    16. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

    17. Install the console box Click here.