STARTER REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE WINDSHIELD WIPER MOTOR AND LINK


    1. Remove the windshield wiper motor and link Click here.

  3. SEPARATE HOSE BRACKET (for LHD)


    1. A019P7C

      Remove the 2 nuts and separate the hose bracket from the outer cowl top panel sub-assembly.

  4. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    1. A019O7N

      Disconnect the connector (w/ Windshield Deicer).

    2. Disengage the grommet and clamp, and separate the wire harness.

    3. A019OCL

      Remove the 6 nuts, 4 bolts and outer cowl top panel sub-assembly.

  5. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    1. A019N0P

      Disconnect the connector (w/ Windshield Deicer).

    2. Disengage the grommet and clamp, and separate the wire harness.

    3. A019OF3

      Remove the 6 nuts, 4 bolts and outer cowl top panel sub-assembly.

  6. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    1. A019KNK

      Lift the rear of the No. 1 engine cover sub-assembly to detach the cover from the 2 pins, and then lift the front of the No. 1 engine cover sub-assembly to detach the cover from the pin and remove the No. 1 engine cover sub-assembly.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. REMOVE NO. 2 AIR CLEANER INLET


    1. A019ODB

      Remove the 2 bolts and No. 2 air cleaner inlet.

  9. REMOVE NO. 1 AIR CLEANER INLET


    1. A019LTK

      Remove the bolt and No. 1 air cleaner inlet.

  10. REMOVE BATTERY


    1. Disconnect the positive (+) cable from the positive (+) battery terminal.

    2. A019LTJ

      Loosen the nut, and remove the bolt from the battery clamp.

    3. Remove the battery and battery tray.

  11. REMOVE AIR CLEANER ASSEMBLY


    1. A019ON2

      Disconnect the vacuum switching valve connector and fuel vapor feed hose.

    2. Disconnect the mass air flow meter connector and separate the wire harness clamp from the air cleaner.

    3. A019MRD

      Disconnect the No. 2 fuel vapor feed hose from the vacuum switching valve and air cleaner hose.

    4. A019KQV

      Disconnect the vacuum switching valve connector and 2 wire harness clamps from the air cleaner.

    5. A019M7X

      Disconnect the ventilation hose from the cylinder head cover.

    6. A019MIG

      Disconnect the vacuum hose and separate it from the 2 hose clamps of the air cleaner hose.

    7. Loosen the bolt of the hose clamp and disconnect the air cleaner hose from the throttle body assembly.

    8. A019M9R

      Remove the 2 bolts and move the air cleaner assembly upward to disengage and remove it from the throttle body assembly.

  12. REMOVE AIR CLEANER BRACKET


    1. A019PFR

      Disconnect the engine wire clamp.

    2. Remove the 2 bolts and air cleaner bracket.

  13. REMOVE STARTER ASSEMBLY


    1. A019K4AE01

      Disconnect the starter connector.

    2. Turn back the terminal cap, remove the nut and disconnect the starter wire.

    3. A019LZI

      Remove the 2 bolts and starter.