OIL AND OIL FILTER REPLACEMENT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

  • In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    3. Clean and install a new gasket and the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  2. REMOVE OIL FILTER ELEMENT


    1. A019KP7E06
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A019NDF

      Remove the oil filter drain plug from the oil filter cap.

    3. A019LNCE04
      Text in Illustration
      *1 Valve
      *2 Cap
      *3 O-ring
      *4 Pipe

      Install the pipe to the oil filter cap.

      Note

      If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

      Tech Tips

      Use a container to catch the draining oil.

    4. A019MZ6

      Check that the oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.

    5. A019MVIE02
      Text in Illustration
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. A019K88E04
      Text in Illustration
      *1 Oil Filter Element
      *2 O-ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.

  3. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, its threads and its O-ring groove.

    2. A019PM2E01
      Text in Illustration
      *1 O-ring
      *a CORRECT
      *b INCORRECT

      Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element into the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

      Note

      Make sure that the O-ring does not get caught between the parts.

    6. A019LV9E01
      Text in Illustration
      *1 Oil Filter Cap
      *2 O-ring
      *3 Oil Filter Bracket
      *a No Gap

      Using SST, install the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

    7. Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

      Note

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. A019N6IE04
      Text in Illustration
      *1 O-ring

      Install the oil filter drain plug.

      Torque:
      13 N*m  { 127 kgf*cm, 10 ft.*lbf }

      Note

      Be careful that the O-ring does not get caught between any surrounding parts.

  4. ADD ENGINE OIL


    1. Add new oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)

      • API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20


      • 5W-20


      • 5W-30


      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40


      • 20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill with oil filter change 4.4 liters (4.6 US qts, 3.9 Imp. qts)
      Drain and refill without oil filter change 4.0 liters (4.2 US qts, 3.5 Imp. qts)
      Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)

    2. Install the oil filler cap.

  5. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  6. INSPECT ENGINE OIL LEVEL


    1. Warm up and stop the engine, then wait for 5 minutes.

    2. Check that the oil level is between the low level and full level marks on the level dipstick.

      If the level is low, check for leakage and add oil up to the full level mark.

      Note

      Do not fill the engine with oil to above the full level mark.