RADIATOR REMOVAL


  1. PRECAUTION (w/ Air Suspension)

    CAUTION:

    Be sure to read Precaution thoroughly before service Click here.

  2. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  3. REMOVE NO. 1 ENGINE UNDER COVER

  4. REMOVE FRONT BUMPER ASSEMBLY (for Standard)

    Click here

  5. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug.

    2. Loosen the cylinder block drain cock plug. (for Bank 1)

    3. Loosen the cylinder block drain cock plug. (for Bank 2, w/ Cylinder Block Drain Cock Plug)

    4. Remove the radiator cap sub-assembly.

      A019LCUE03
      Text in Illustration
      *1 Radiator Cap Sub-assembly *2 Cylinder Block Drain Cock Plug (for Bank 1)
      *3 Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug) *4 Radiator Drain Cock Plug
      *5 Air Drain Cock Plug - -

      Tech Tips

      Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  6. REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A019LVN

      Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 retainers on the front of the V-bank cover sub-assembly. Continue to raise the V-bank cover sub-assembly to disengage the 2 retainers on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

      Note

      Attempting to disengage both front and rear retainers at the same time may cause the V-bank cover sub-assembly to break.

  7. REMOVE NO. 2 AIR CLEANER INLET


    1. A019O60

      Disconnect the 2 vacuum hose clamps from the No. 2 air cleaner inlet.

    2. Remove the 2 bolts and No. 2 air cleaner inlet.

  8. REMOVE NO. 1 AIR CLEANER INLET


    1. A019ND6

      Disconnect the vacuum hose clamp from the No. 1 air cleaner inlet.

    2. Remove the bolt and No. 1 air cleaner inlet.

  9. REMOVE BATTERY


    1. Disconnect the positive (+) cable from the positive (+) battery terminal.

    2. A019LTJ

      Loosen the nut, and remove the bolt from the battery clamp.

    3. Remove the battery and battery tray.

  10. REMOVE RADIATOR RESERVE TANK ASSEMBLY


    1. A019OG6

      Disconnect the radiator reserve tank hose from the radiator.

    2. A019N1D

      Disconnect the 2 clamps and remove the bolt and radiator reserve tank from the radiator.

  11. DISCONNECT NO. 1 RADIATOR HOSE


    1. A019JYY

      Disconnect the No. 1 radiator hose from the radiator.

  12. DISCONNECT NO. 2 RADIATOR HOSE


    1. A019K90

      Disconnect the No. 2 radiator hose from the radiator.

  13. DISCONNECT INLET OIL COOLER HOSE


    1. A019JZN

      Disconnect the inlet oil cooler hose and clamp from the radiator.

  14. DISCONNECT OUTLET OIL COOLER HOSE


    1. A019O3J

      Remove the outlet oil cooler hose.

  15. REMOVE MILLIMETER WAVE RADAR SENSOR (w/ Dynamic Radar Cruise Control System)


    1. A019LF9

      Disconnect the connector.

    2. Remove the 3 bolts and the millimeter wave radar sensor assembly.

  16. REMOVE HIGH PITCHED HORN ASSEMBLY (for RHD)


    1. A019LXM

      Disconnect the connector.

    2. Remove the bolt and high pitched horn assembly.

  17. REMOVE LOW PITCHED HORN ASSEMBLY (for LHD)


    1. A019OJ0

      Disconnect the connector.

    2. Remove the bolt and low pitched horn assembly.

  18. REMOVE SMOG VENTILATION SENSOR


    1. A019LDV

      Disconnect the connector.

    2. Remove the bolt

    3. Disengage the guide and remove the smog ventilation sensor.

  19. REMOVE HOOD LOCK CONTROL CABLE COVER

    Tech Tips


    • Remove Hood Lock Control Cable Cover (for LHD) Click here.


    • Remove Hood Lock Control Cable Cover (for RHD) Click here.

  20. REMOVE HOOD LOCK ASSEMBLY

    Tech Tips



  21. REMOVE UPPER RADIATOR SUPPORT


    1. A019P6G

      Disconnect the 3 clamps of the hood lock control cable and remove the 5 bolts and upper radiator support.

  22. REMOVE NO. 2 RADIATOR ASSEMBLY


    1. A019LGWE01
      Text in Illustration
      *1 Radiator support cushion

      Remove the 2 radiator support cushions from the radiator.

    2. A019LUQE01
      Text in Illustration
      *1 Cooler bracket
      *2 Cooler compressor bracket

      Remove the 4 bolts, 4 brackets and radiator assembly.

    3. A019JYN

      Disconnect the 3 wire harness clamps and connector.

    4. A019LAO

      Remove the radiator assembly and fan assembly with motor.

      Note

      Do not apply any excessive force to the cooler condenser assembly or pipe when removing the radiator assembly.

    5. Remove the 2 lower radiator supports from the radiator.

    6. A019N55

      Remove the 2 bolts.

    7. A019LCME01
      Text in Illustration
      *1 Claw
      *2 Guide

      Release the claw and pull up the fan assembly with motor from the radiator assembly to remove the fan assembly with motor.