ECM INSTALLATION


  1. INSTALL ECM


    1. A019PHCE01
      Text in Illustration
      *1 ECM Bracket

      Install the 2 brackets to the ECM with the 5 screws.

    2. A019N7Q

      Install the ECM with bracket with the 3 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 70 in.*lbf }
    3. A019M47

      Connect the 2 ECM connectors and lower the 2 levers.

      Note


      • When connecting the connectors, make sure that dirt, water or other foreign matter does not become stuck between the connectors and other part.

      • Make sure that the 2 levers are securely locked.

    4. Install the wire harness clamp.

    5. A019L5L

      Install the wire harness clamp.

  2. INSTALL AIR CLEANER ASSEMBLY


    1. A019M7QE01
      Text in Illustration
      *1 Tab
      *2 Hole

      Insert the tab of the air cleaner assembly to the hole of the vehicle body as shown in the illustration.

    2. A019JQO

      Install the air cleaner assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. A019L8LE01
      Text in Illustration
      *1 Ventilation Hose
      *2 Fuel Vapor Feed Hose

      Connect the air cleaner hose to the throttle body with the hose clamp.

    4. Connect the ventilation hose and the fuel vapor feed hose.

    5. A019LU3

      Connect the 2 vacuum hoses.

    6. A019KSB

      Connect the 2 wire harness clamps and vacuum switching valve connector.

    7. A019LPG

      Connect the vacuum hose to the intake air surge tank assembly.

    8. Install the hose to the hose clamp.

    9. A019K7G

      Connect the mass air flow meter connector and wire harness clamp.

  3. INSTALL NO. 1 AIR CLEANER INLET


    1. A019ND6

      Install the No. 1 air cleaner inlet with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the vacuum hose clamp to the No. 1 air cleaner inlet.

  4. INSTALL NO. 2 AIR CLEANER INLET


    1. A019O60

      Install the No. 2 air cleaner inlet with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the 2 vacuum hose clamps to the No. 2 air cleaner inlet.

  5. INSTALL BATTERY


    1. Install the battery and battery tray.

    2. A019LTJ

      Install the battery clamp with the bolt and nut.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the positive (+) cable to the positive (+) battery terminal.

      Torque:
      6.4 N*m  { 65 kgf*cm, 57 in.*lbf }

  6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. INSTALL V-BANK COVER SUB-ASSEMBLY


    1. A019LVN

      Fit the 4 retainers and install the V-bank cover sub-assembly.

  8. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    1. A019OCLE01

      Install the outer cowl top panel sub-assembly with the 4 bolts, 4 nuts*1 and 2 nuts*2.

      Torque:
      Nut*1
      85 N*m  { 867 kgf*cm, 63 ft.*lbf }
      Nut*2
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Bolt
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A019O7N

      Engage the grommet and clamp to install the wire harness.

    3. Connect the connector (w/ Windshield Deicer).

  9. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    1. A019OF3E01

      Install the outer cowl top panel sub-assembly with the 4 bolts, 4 nuts*1 and 2 nuts*2.

      Torque:
      Nut*1
      85 N*m  { 867 kgf*cm, 63 ft.*lbf }
      Nut*2
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Bolt
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A019N0P

      Engage the grommet and clamp to install the wire harness.

    3. Connect the connector (w/ Windshield Deicer).

  10. INSTALL FRONT SHOCK ABSORBER CAP (w/ Air Suspension)


    1. A019N7O

      Install the front shock absorber cap with the 3 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

  11. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. Install the windshield wiper motor and link assembly Click here.

  12. PERFORM INITIALIZATION

    Tech Tips

    Initialization cannot be completed by only disconnecting and reconnecting the cable of the negative (-) battery terminal.


    1. Perform Initialization when replacing the ECM Click here.