THROTTLE BODY REMOVAL


  1. REMOVE PRECAUTION (w/ Navigation System for HDD)

    Note

    After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE NO. 1 ENGINE UNDER COVER

  4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  5. SEPARATE HOSE BRACKET (for LHD)


    1. A019P7C

      Remove the 2 nuts and separate the hose bracket from the outer cowl top panel sub-assembly.

  6. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    1. Place the front tires on the ground.

    2. A019O7N

      Disconnect the connector (w/ Windshield Deicer).

    3. Disengage the grommet and clamp, and separate the wire harness.

    4. A019OCLE03

      Remove the 6 nuts, 4 bolts and outer cowl top panel sub-assembly.

    5. Temporarily tighten the 4 nuts (A) to support the front shock absorber.

  7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    1. Place the front tires on the ground.

    2. A019N0P

      Disconnect the connector (w/ Windshield Deicer).

    3. Disengage the grommet and clamp, and separate the wire harness.

    4. A019OF3E02

      Remove the 6 nuts, 4 bolts and outer cowl top panel sub-assembly.

    5. Temporarily tighten the 4 nuts (A) to support the front shock absorber.

  8. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    1. A019KNK

      Lift the rear of the No. 1 engine cover sub-assembly to detach the cover from the 2 pins, and then lift the front of the No. 1 engine cover sub-assembly to detach the cover from the pin and remove the No. 1 engine cover sub-assembly.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.

  9. DRAIN ENGINE COOLANT


    1. Loosen the radiator drain cock and drain the coolant.

      CAUTION:

      Do not remove the radiator cap and radiator drain cock while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. Loosen the air drain valve.

    3. Remove the radiator cap from the radiator assembly.

      A019K3KE01
      Text in Illustration
      *1 Air Drain valve *2 Radiator Cap Sub-assembly
      *3 Radiator Drain Cock - -

  10. REMOVE NO. 2 AIR CLEANER INLET


    1. A019MRA

      Remove the 2 bolts and No. 2 air cleaner inlet.

  11. REMOVE NO. 1 AIR CLEANER INLET


    1. A019K2I

      Remove the bolt and No. 1 air cleaner inlet.

  12. REMOVE BATTERY


    1. Disconnect the positive (+) cable from the positive (+) battery terminal.

    2. A019LTJ

      Loosen the nut, and remove the bolt from the battery clamp.

    3. Remove the battery and battery tray.

  13. REMOVE AIR CLEANER ASSEMBLY


    1. A019ON2

      Disconnect the vacuum switching valve connector and fuel vapor feed hose.

    2. Disconnect the mass air flow meter connector and separate the wire harness clamp from the air cleaner.

    3. A019MRD

      Disconnect the No. 2 fuel vapor feed hose from the vacuum switching valve and air cleaner hose.

    4. A019KQV

      Disconnect the vacuum switching valve connector and 2 wire harness clamps from the air cleaner.

    5. A019M7X

      Disconnect the ventilation hose from the cylinder head cover.

    6. A019MIG

      Disconnect the vacuum hose and separate it from the 2 hose clamps of the air cleaner hose.

    7. Loosen the bolt of the hose clamp and disconnect the air cleaner hose from the throttle body assembly.

    8. A019M9R

      Remove the 2 bolts and move the air cleaner assembly upward to disengage and remove it from the throttle body assembly.

  14. REMOVE THROTTLE BODY ASSEMBLY


    1. A019JYQ

      Disconnect the throttle body assembly connector.

    2. Disconnect the fuel tube from the clamp.

    3. A019NIS

      Disconnect the 2 water by-pass hoses from the throttle body assembly.

    4. A019KSC

      Remove the 4 bolts and the throttle body assembly.

    5. A019NYI

      Remove the bolt and fuel tube bracket.

    6. A019LMP

      Remove the gasket from the intake manifold.