REPAIR INSTRUCTION CUSTOMIZE PARAMETERS

Note


  • When the customer requests a change in a function, first make sure that the function can be customized.

  • Be sure to make a note of the current settings before customizing.

  • When troubleshooting a function, first make sure that the function is set to the default setting.

Tech Tips

The following items can be customized.


  1. POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

    Tilt & Telescopic
    Display Default Content Setting
    Auto away/Return function ON Turn the auto away/return function ON/OFF ON / OFF

  2. LEXUS PARKING ASSIST-SENSOR SYSTEM (w/ Side Monitor System)


    1. Customizing with the intelligent tester

      Warning
      Display Default Content Setting Relevant ECU
      Fr Sensor Onset Range Wide Sets the detection operation range for the front center sensors.

      Narrow or Wide


      • Narrow: 500 mm (19.7 in.)

      • Wide: 1000 mm (39.4 in.)

      		 Parking assist ECU
      Rr Sensor Onset Range Wide Sets the detection operation range for the rear center sensors.

      Narrow or Wide


      • Narrow: 600 mm (23.6 in.)

      • Wide: 1500 mm (59.1 in.)

      		 Parking assist ECU
      Keep Sense Buzzer Avail Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.

      Not Avail or Avail


      • Not Avail: Not Available

      • Avail: Available

      		 Parking assist ECU
      Fr & Rr Buzzer Volume M2 Changes the buzzer volume setting.

      L, M1, M2, M3 or H


      • L: Low volume

      • M1: Medium low volume

      • M2: Medium volume

      • M3: Medium high volume

      • H: High volume

      		 Parking assist ECU
      Sensor
      Display Default Content Setting Relevant ECU
      Sensor Condition N Avail Makes the front sensors available when the shift lever is in N.

      Not Avail or Avail


      • Not Avail: Not Available

      • Avail: Available

      		 Parking assist ECU
      Reverse Range Front Sensor Fcrn Changes the operation setting for the front sensors when the shift lever is in R.

      F, Fcrn or F Stop


      • F: All front sensors are available

      • Fcrn: Front corner sensors are available

      • F Stop: All Front sensors are not available

      		 Parking assist ECU
      Non P/R Range Rear Sensor R Stop Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.

      R, Rcrn or R Stop


      • R: All rear sensors are available

      • Rcrn: Rear corner sensors are available

      • R Stop: All rear sensors are not available

      		 Parking assist ECU
      Display
      Display Default Content Setting Relevant ECU
      Display Mode All The display mode setting (when the Lexus parking assist-sensor system is normal). All or Undisp Parking assist ECU

    2. Customizing with Multi-display

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Turn the engine switch on (IG).

      2. Turn the Lexus parking assist-sensor system on.

      3. Select the following menus: Setup / Vehicle / LEXUS park assist.

      4. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Alert volume 3 Sets the buzzer alert volume.

        1, 2, 3, 4 or 5


        • 1: Low volume

        • 2: Medium low volume

        • 3: Medium volume

        • 4: Medium high volume

        • 5: High volume

        		 Parking assist ECU
        Display On The display mode setting (when the Lexus parking assist-sensor system is normal). On or Off Parking assist ECU
        Distance FRONT Wide Sets the detection operation range for the front center sensors.

        Narrow or Wide


        • Narrow: 500 mm (19.7 in.)

        • Wide: 1000 mm (39.4 in.)

        		 Parking assist ECU
        Distance REAR Wide Sets the detection operation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1500 mm (59.1 in.)

        		 Parking assist ECU

  3. LEXUS PARKING ASSIST-SENSOR SYSTEM (w/o Side Monitor System)


    1. Customizing with the intelligent tester

      Warning
      Display Default Content Setting Relevant ECU
      Fr Sensor Onset Range Wide Sets the detection operation range for the front center sensors.

      Narrow or Wide


      • Narrow: 500 mm (19.7 in.)

      • Wide: 1000 mm (39.4 in.)

      		 Clearance warning ECU assembly
      Rr Sensor Onset Range Wide Sets the detection operation range for the rear center sensors.

      Narrow or Wide


      • Narrow: 600 mm (23.6 in.)

      • Wide: 1500 mm (59.1 in.)

      		 Clearance warning ECU assembly
      Keep Sense Buzzer Avail Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.

      Not Avail or Avail


      • Not Avail: Not Available

      • Avail: Available

      		 Clearance warning ECU assembly
      Fr & Rr Buzzer Volume M2 Changes the buzzer volume setting.

      L, M1, M2, M3 or H


      • L: Low volume

      • M1: Medium low volume

      • M2: Medium volume

      • M3: Medium high volume

      • H: High volume

      		 Clearance warning ECU assembly
      Sensor
      Display Default Content Setting Relevant ECU
      Sensor Condition N Avail Makes the front sensors available when the shift lever is in N.

      Not Avail or Avail


      • Not Avail: Not Available

      • Avail: Available

      		 Clearance warning ECU assembly
      Reverse Range Front Sensor Fcrn Changes the operation setting for the front sensors when the shift lever is in R.

      F, Fcrn or F Stop


      • F: All front sensors are available

      • Fcrn: Front corner sensors are available

      • F Stop: All Front sensors are not available

      		 Clearance warning ECU assembly
      Non P/R Range Rear Sensor R Stop Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.

      R, Rcrn or R Stop


      • R: All rear sensors are available

      • Rcrn: Rear corner sensors are available

      • R Stop: All rear sensors are not available

      		 Clearance warning ECU assembly
      Display
      Display Default Content Setting Relevant ECU
      Display Mode*1 All The display mode setting (when the Lexus parking assist-sensor system is normal). All or Undisp Clearance warning ECU assembly

      • *1: This item is used to allow or prevent the LEXUS parking assist-sensor system from being displayed on the multi display assembly. For this model, some vehicles are not equipped with the multi display assembly. For those vehicles, the Display Mode item is not available.

    2. Customizing with Multi-display

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Turn the engine switch on (IG).

      2. Turn the Lexus parking assist-sensor system on.

      3. Select the following menus: Setup / Vehicle / LEXUS park assist.

      4. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Alert volume 3 Sets the buzzer alert volume.

        1, 2, 3, 4 or 5


        • 1: Low volume

        • 2: Medium low volume

        • 3: Medium volume

        • 4: Medium high volume

        • 5: High volume

        		 Clearance warning ECU assembly
        Display On The display mode setting (when the Lexus parking assist-sensor system is normal). On or Off Clearance warning ECU assembly
        Distance FRONT Wide Sets the detection operation range for the front center sensors.

        Narrow or Wide


        • Narrow: 500 mm (19.7 in.)

        • Wide: 1000 mm (39.4 in.)

        		 Clearance warning ECU assembly
        Distance REAR Wide Sets the detection operation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1500 mm (59.1 in.)

        		 Clearance warning ECU assembly

  4. POWER DOOR LOCK CONTROL SYSTEM


    1. Customizing with the intelligent tester

      Door Lock
      Display Default Content Setting
      Unlock Key Twice*1 ON or OFF Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. ON or OFF
      Auto Lock*2 ON Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF
      Auto Lock/Shift*2 OFF Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. ON or OFF
      Auto Unlock/Shift OFF Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). ON or OFF
      All Unlock/Open-Close*1 ON or OFF Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the engine switch is turned off. ON or OFF

      • *1: Default setting differs depending on the country.

      • *2: w/ Customizable Auto Lock Function

      Illuminated Entry
      Display Default Content Setting
      Lighting Time 15 s Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the engine switch from off to on (ACC) or on (IG).) 7.5 s, 15 s or 30 s

    2. Customizing with the multi-display (w/ Navigation System)


      1. Turn the engine switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Unlock on second key turn*1 On or Off Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. On or Off Main body ECU (Multiplex network body ECU)
        Speed sensitive auto locking*2 On Function that locks all doors when the vehicle speed reaches a certain level. On or Off Main body ECU (Multiplex network body ECU)
        Auto lock by shift from P*2 Off Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by shift to P On Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by driver door*1 On or Off Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the engine switch is turned off. On or Off Main body ECU (Multiplex network body ECU)

        • *1: Default setting differs depending on the country.

        • *2: w/ Customizable Auto Lock Function

    3. Customizing with the multi-display (w/o Navigation System)


      1. Turn the engine switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Speed sensitive auto locking*2 On Function that locks all doors when the vehicle speed reaches a certain level. On or Off Main body ECU (Multiplex network body ECU)
        Auto lock by shift from P*2 Off Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by shift to P On Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by driver door*1 On or Off Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the engine switch is turned off. On or Off Main body ECU (Multiplex network body ECU)

        • *1: Default setting differs depending on the country.

        • *2: w/ Customizable Auto Lock Function

  5. CUSTOMIZING FUNCTION WITH COMBINATION METER ASSEMBLY (POWER DOOR LOCK CONTROL SYSTEM)

    Tech Tips


    • Press and hold the ENTER switch on the steering pad switch assembly when entering an item.

    • Briefly press the ENTER switch on the steering pad switch assembly when selecting an item.


    1. Turn the engine switch on (IG).

    2. Press and hold the ENTER switch on the steering pad switch assembly.

    3. Select the setting by referring to the table below

      Display Default Content Setting Relevant ECU
      SPEED SENSITIVE AUTO. LOCK*2 ON Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF Main body ECU (Multiplex network body ECU)
      SHIFT-LINKED AUTOMATIC LOCK*2 OFF Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. ON or OFF Main body ECU (Multiplex network body ECU)
      SHIFT-LINKED AUTOMATIC UNLOCK ON Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG). ON or OFF Main body ECU (Multiplex network body ECU)
      DRIVER DOOR-LINKED UNLOCK*1 ON or OFF Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the engine switch is turned off. ON or OFF Main body ECU (Multiplex network body ECU)

      • *1: Default setting differs depending on the country.

      • *2: w/ Customizable Auto Lock Function

    4. Press and hold the ENTER switch on the steering pad switch assembly.

    5. The setting completion screen will be displayed.

    6. Return to the item selection screen.

  6. WIRELESS DOOR LOCK CONTROL SYSTEM


    1. Customizing with the intelligent tester

      Wireless Door Lock Control System
      Display (item) Default Function Setting
      Wireless Control ON Function that turns wireless door lock / ON or OFF ON or OFF
      Hazard Answer Back ON

      When the doors are locked by wireless operation, the hazard warning lights flash once.

      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

      		 ON or OFF
      Open Door Warning*1 ON The buzzer sounds when lock is pressed when any of the doors are ajar. ON or OFF
      Unlock 2 Operation*2 ON or OFF Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON or OFF
      Panic Function*3 ON Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds ON or OFF
      Auto Lock Time 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s
      Wireless Buzzer Resp*4 ON Wireless door lock buzzer response / ON or OFF ON or OFF
      P/W Wireless Ope Buzz*5 ON Wireless power window buzzer response / ON or OFF ON or OFF
      Wireless Buzzer Vol*1 Level 7 Wireless door lock buzzer Volume Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0

      • *1: w/ Door ajar warning function

      • *2: Default setting differs depending on the country.

      • *3: w/ Panic function

      • *4: w/ Wireless buzzer answer back function

      • *5: w/ Wireless power window buzzer response function

      Illuminated Entry
      Display Default Content Setting
      Lighting Time 15 s Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the engine switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s

    2. Customizing with the multi-display (w/ Navigation System)


      1. Turn the engine switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Remote 2-press unlock*1 On or Off Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. On or Off Main body ECU (Multiplex network body ECU)
        Lock/unlock feedback-lights On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off Main body ECU (Multiplex network body ECU)
        Lock/unlock feedback-tone*2 7 Wireless door lock buzzer Volume Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

        • *1: Default setting differs depending on the country.

        • *2: w/ Door ajar warning function

    3. Customizing with the multi-display (w/o Navigation System)


      1. Turn the engine switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Remote 2-press unlock*1 On or Off Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. On or Off Main body ECU (Multiplex network body ECU)
        Lock/unlock feedback-lights On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off Main body ECU (Multiplex network body ECU)
        Lock/unlock feedback-tone*2 7 Wireless door lock buzzer Volume Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

        • *1: Default setting differs depending on the country.

        • *2: w/ Door ajar warning function

  7. CUSTOMIZING FUNCTION WITH COMBINATION METER ASSEMBLY (WIRELESS DOOR LOCK CONTROL SYSTEM)

    Tech Tips


    • Press and hold the ENTER switch on the steering pad switch assembly when entering an item.

    • Briefly press the ENTER switch on the steering pad switch assembly when selecting an item.


    1. Turn the engine switch on (IG).

    2. Press and hold the ENTER switch on the steering pad switch assembly

    3. Select the setting by referring to the table below

      Display Default Content Setting Relevant ECU
      REMOTE 2-PRESS UNLOCK*1 ON or OFF Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON or OFF Main body ECU (Multiplex network body ECU)
      LOCK/UNLOCK ANSWER BACK ON

      When the doors are locked by wireless operation, the hazard warning lights flash once.

      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

      		 ON or OFF Main body ECU (Multiplex network body ECU)
      LOCK FEEDBACK VOLUME*2 7 Wireless door lock buzzer volume 0, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

      • *1: Default setting differs depending on the country.

      • *2: w/ Door ajar warning function

    4. Press and hold the ENTER switch on the steering pad switch assembly.

    5. The setting completion screen will be displayed.

    6. Return to the item selection screen.

  8. ENTRY AND START SYSTEM (for Entry Function)


    1. Customizing with intelligent tester.

      Entry & Start
      Tester Display Default Content Setting
      Ignition Available Area All Function that switches the entry ignition detection area Front or All
      Park Wait Time 2.5 s Function that sets waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s, or 5 s
      Back Door Opening Operation Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF
      Warning
      Tester Display Default Content Setting
      Key Low Battery Warning ON Function that warns driver that key battery is weak ON or OFF

    2. Customizing with the multi-display (w/ Navigation System)


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Select Doors to Unlock Driver's Door Function that sets which doors are unlocked by the entry unlock function. All Doors or Driver's Door Certification ECU (smart key ECU assembly)
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the multi-display (w/ Audio and Visual System (w/ Multi-display))


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Select doors to unlock Driver's Door Function that sets which doors are unlocked by the entry unlock function. All Doors or Driver's Door Certification ECU (smart key ECU assembly)
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

  9. ENTRY UNLOCK MODE SWITCHING

    Note

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.


    1. To change the vehicle entry unlock mode, make sure that the vehicle power is off and simultaneously push and hold the key lock switch and another key switch for 5 seconds.

      When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

      Note

      After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.


      • Driver door unlock mode:

        When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

      • All door unlock mode:

        When any touch sensor is touched, all doors unlock.

    2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the entry and start system to the entry unlock mode.

    3. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly and combination meter assembly (buzzer) to inform the user that the mode has been changed.


      1. for except Europe and China

        Mode Wireless Door Lock Buzzer Assembly Combination Meter Assembly (Buzzer)

        Driver Door

        (Default)

        		 Sounds 3 times Sounds once

        All Doors

        (Customized)

        		 Sounds 2 times Sounds once

        Tech Tips

        The procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

      2. for Europe and China

        Mode Wireless Door Lock Buzzer Assembly Combination Meter Assembly (Buzzer)

        Driver Door

        (Customized)

        		 Sounds 3 times Sounds once

        All Doors

        (Default)

        		 Sounds 2 times Sounds once

        Tech Tips

        The procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

  10. ELECTRICAL KEY CANCEL

    Note

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation.

    The electrical key cancel operation disables the following functions:


    • Entry Unlock/Lock

    • Entry Ignition

    • Entry Back Door Open

    • Electrical Key Lock-in Prevention

    • Warning

    • Memory Call


    1. The operation procedures are as follows:

      Precondition:

      Engine switch off, driver side door closed and unlocked.


      1. Push the unlock switch of the key once.

      2. Open the driver door within 5 seconds.

      3. Push the unlock switch of the key twice within 5 seconds.

      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.

      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

  11. ENTRY AND START SYSTEM (for Start Function)


    1. Customizing with intelligent tester.

      Entry & Start
      Tester Display Default Content Setting
      Ignition Available Area (Entry ignition available area) All Function to choose the available area for electrical key to start the engine and cancel the steering lock. Front or All
      Key Low Battery Warning ON Function to warning driver that the key battery is low. ON or OFF

    2. Customizing with the multi-display (w/ Navigation System)


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the multi-display (w/ Audio and Visual System (w/ Multi-display))


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

  12. CUSTOMIZING FUNCTION WITHOUT INTELLIGENT TESTER (ENTRY AND START SYSTEM (for Start Function))

    Performing the following procedure disables the entry and start system.

    Tech Tips

    To start the engine while the entry and start system is disabled, follow the procedure for when the key battery is low Click here.


    1. The operation procedures are as follows:

      Precondition:

      Engine switch off, driver side door closed and unlocked.


      1. Push the unlock switch of the key once.

      2. Open the driver door within 5 seconds.

      3. Push the unlock switch of the key twice within 5 seconds.

      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.

      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

  13. THEFT DETERRENT SYSTEM (w/ Intrusion Sensor)

    Theft Deterrent System (w/ Intrusion Sensor)
    Display (item) Default Function Setting
    Intrusion Win Opened OFF This function sets the sensitivity of the intrusion sensor when a door window is open ON or OFF
    Security control with mechanism key OFF This function set to be able to release security alarm with the mechanism key ON or OFF

  14. THEFT DETERRENT SYSTEM (w/o Intrusion Sensor)

    Theft Deterrent System (w/o Intrusion Sensor)
    Display (item) Default Function Setting
    Security control with mechanism key OFF This function set to be able to release security alarm with the mechanism key ON or OFF

  15. LIGHTING SYSTEM (LIGHTING INT)


    1. Customizing with the Intelligent tester

      Illuminated Entry
      Tester Display Default Content Setting Relevant ECU
      Lighting Time 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the engine switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF ON Lights up engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when the engine switch is turned from on (ACC or IG) to off. ON or OFF
      I/L ON W/Door Key Unlock ON Lights up engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when doors are unlocked using a mechanical key or door control transmitter. ON or OFF
      Room Light when Aprchd ON Lights up the engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when a key enters any actuation area around the doors. ON or OFF
      Center Console Spot Light ON Lights up the center console spot light when engine switch is turned on (ACC or IG) ON or OFF
      Interior Light Control ON Change the interior lights (engine switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights) control. ON or OFF

    2. Customizing using the Multi-display


      1. Turn the engine switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Lights Settings.

      3. Select the setting by referring to the table below:

        Display Default Content Setting Relevant ECU
        Interior Lights Off Timer 15 sec. Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the engine switch from off to on (ACC or IG).) Off, 7.5 sec., 15 sec., or 30 sec. Main body ECU (Multiplex network body ECU)

    3. Customizing using the Combination meter assembly

      Tech Tips


      • Press the UP/DOWN switch on the steering pad switch assembly when changing an item selection.

      • Press the ENTER switch on the steering pad switch assembly when selecting an item.


      1. Turn the engine switch on (IG).

      2. Press and hold the MENU switch on the steering pad switch assembly.

      3. Select the setting by referring to the table below:

        Display Default Content Setting Relevant ECU
        INTERIOR LIGHTS OFF TIME ADJUSTMENT 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the engine switch from off to on (ACC or IG).) Off, 7.5 s, 15 s, or 30 s Main body ECU (Multiplex network body ECU)

      4. Press the ENTER switch on the steering pad switch assembly.

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

  16. METER / GAUGE SYSTEM

    Warning
    Tester Display Default Content Setting
    Driver Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the driver side seat belt warning buzzer ON / OFF
    Front Passenger Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the front passenger side seat belt warning buzzer ON / OFF

    *1: This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

    Display
    Tester Display Default Content Setting
    ECO Drive Indicator ON Function to turn on/off the ECO driving indicator zone display in the multi-information display ON / OFF

  17. FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)


    1. Customizing with the Intelligent tester

      Main Body
      Tester Display Default Content Setting
      Seat Move Distance Standard Allows customizing of the seat movement distance for the power easy access system. OFF / Little / Standard
      Movable Seat Select D Seat Allows customizing of whether the driver seat operates due to smart entry unlock operation of only the driver door, or all seats operate due to smart entry unlock operation of all doors. D Seat / All Seat

    2. Customizing with the multi-display


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Settings / Vehicle Customization / Other Vehicle Settings

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Driver's Seat Easy Exit Full Allows customizing of the seat movement distance for the power easy access system. Full / Partial / Off Front power seat switch (driver side)

  18. CUSTOMIZING FUNCTION WITH COMBINATION METER ASSEMBLY (FRONT POWER SEAT CONTROL SYSTEM (w/ Memory))

    Tech Tips


    • Press the UP/DOWN switch on the steering pad switch assembly when changing an item selection.

    • Press the ENTER switch on the steering pad switch assembly when selecting an item.


    1. Turn the engine switch on (IG).

    2. Press and hold the MENU switch on the steering pad switch assembly.

    3. Select the setting by referring to the table below

      Display Default Content Setting Relevant ECU
      DRIVER'S SEAT EASY EXIT FULL Allows customizing of the seat movement distance for the power easy access system. FULL / PARTIAL / OFF Front power seat switch (driver side)

    4. Press the ENTER switch on the steering pad switch assembly.

    5. The setting completion screen will be displayed.

    6. Return to the item selection screen.

  19. SEAT BELT WARNING SYSTEM

    Combination Meter
    Tester Display Default Content Setting
    Driver Side Seatbelt Warning Buzzer* ON Function to sound the seat belt warning buzzer ON/OFF
    Front Passenger Side Seatbelt Warning Buzzer* ON Function to sound the seat belt warning buzzer ON/OFF

    *: This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

  20. AIR CONDITIONING SYSTEM


    1. Customizing with the Intelligent tester

      Air Conditioner
      Display (Item) Default Content Setting
      Set Temperature Shift Normal Function to control with the shifted temperature against the displayed temperature -2 C, -1 C, Normal, +1 C or +2 C
      Emission Gas Sensor Shift*1 Normal Function to change the sensitivity of the exhaust gas sensor Much Less, Less, Little Less, Normal, Little More, More, Much More
      Evaporator Control Automatic Function to set the evaporator control to the automatic position (AUTO) to save power, or to the coldest position (MANUAL) to dehumidify air and to prevent the windows from fogging up Automatic or Manual
      Compressor/Air Inlet DEF operation LINK Function to automatically turn the A/C on linked with the FRONT DEF button when the A/C is off NORMAL or LINK
      Compressor Mode Automatic Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off Automatic or Manual
      Air Inlet Mode Automatic Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on Automatic or Manual
      Foot/DEF Auto Mode ON Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on OFF or ON
      Foot/DEF Automatic Blow Up Function ON Function to automatically increase the blower level when the defroster is on OFF or ON
      Ambient Temperature Shift Normal Function to control the shifted ambient temperature in relation to the displayed ambient temperature -3 C, -2 C, -1 C, Normal, +1 C, +2 C or +3 C
      ECO MODE Cancel OFF Function to cancel the ECO mode drive when item is on OFF or ON

      • *1: w/ Smog Ventilation Sensor

    2. Customizing with the multi-display


      1. Turn the engine switch to ON.

      2. Enter the following menus: Setup / Vehicle / Vehicle Settings / Climate Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Smog Sensor Sensitivity*1 0 Function to change the sensitivity of the exhaust gas sensor -3, -2, -1, 0, +1, +2, +3 Air conditioning amplifier assembly
        Auto A/C Mode On Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off On or Off Air conditioning amplifier assembly
        Efficient Ventilation Mode On In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode On or Off Air conditioning amplifier assembly

        • *1: w/ Smog Ventilation Sensor

  21. POWER WINDOW CONTROL SYSTEM

    Power Window
    Tester Display Default Content Setting
    Door Key Linked P/W Up ON This function is used to close the windows by operating the mechanical key. ON/OFF
    Door Key Linked P/W Down ON This function is used to open the windows by operating the mechanical key. ON/OFF
    P/W Up w/ Transmitter OFF This function is used to close the windows using the wireless key transmitter. ON/OFF
    P/W Down w/ Transmitter OFF This function is used to open the windows using the wireless key transmitter. ON/OFF
    P Window Auto Up Avail This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger side). Avail/Not Avl
    P Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly. Avail/Not Avl
    RR Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH side). Avail/Not Avl
    RR Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly. Avail/Not Avl
    RL Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH side). Avail/Not Avl
    RL Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly. Avail/Not Avl
    Close All P/W Function ON This function is used to close the windows by suggest mode function. ON/OFF

  22. SLIDING ROOF SYSTEM

    Sliding Roof
    Tester Display Default Content Setting
    Door Key Related Open*1 ON Function to manually open sliding roof linked with power windows by holding driver side door key for 1.5 seconds or more to unlock position when engine switch is off ON/OFF
    Door Key Related Close*1 ON Function to manually close sliding roof linked with power windows by holding driver side door key for 1.5 seconds or more to lock position when engine switch is off ON/OFF
    Wireless Key Related Open*2 OFF Function to manually open sliding roof linked with power windows by pressing transmitter UNLOCK switch for 2.5 seconds or more when engine switch is off ON/OFF
    Wireless Key Related Close*2 OFF Function to manually close sliding roof linked with power windows by pressing transmitter LOCK switch for 2.5 seconds or more when engine switch is off ON/OFF
    Door Key Related Operation Slide Function to select tilt up or slide open of manual sliding roof operation linked with power windows by holding driver side door key for 1.5 seconds or more to unlock position when engine switch is off Tilt/Slide
    Wireless Key Related Operation Slide Function to select tilt up or slide open of manual sliding roof operation linked with power windows by pressing on transmitter UNLOCK switch for 2.5 seconds or more when engine switch is off Tilt/Slide

    • *1: This function is linked with the power window key-linked function. If the power window key-linked function is set to OFF, the sliding roof key-linked function will not operate even when it is set to ON.

    • *2: This function is linked with the power window wireless transmitter-linked function. If the power window wireless transmitter-linked function is set to OFF, the sliding roof wireless transmitter-linked function will not operate even when it is set to ON.

  23. POWER BACK DOOR SYSTEM

    PSD&PBD operation
    Tester Display Default Content Setting
    PBD SW Operation 0.8 s Function that turns the power back door closer switch on when a switch is pushed once or held down for 0.8 seconds. 0.8 s or ON
    PBD Buzzer In Use*1 OFF Function that makes the power back door buzzer sound when the power back door is operating. OFF or ON
    Door unlock with 1 motion*2 ALL DOORS Function that selects the door or doors to unlock when the back door is locked and the transmitter switch is pushed to operate the power back door. Back Door or ALL DOORS
    One Motion

    (Not Use)*2, *4

    0.8 s*3

    		 Function that operates the power back door by pushing the transmitter switch when the back door is unlocked. OFF, 1 Op, 2 Op or 0.8 s
    One Motion with unlock door*2 0.8 s Function that operates the power back door by pushing the transmitter switch regardless of the door lock condition. OFF, 2 Op or 0.8 s
    PBD Assist Open Operation*5, *6 OFF Function that enables or disables the power back door assist open operation . When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. OFF or ON

    • *1: The warning buzzer that sounds when the power back door is operating cannot be customized (even if this function is set to "OFF", the buzzer will still sound).

    • *2: w/ Wireless one motion function

    • *3: w/o Wireless one motion function

    • *4: "Not Use" is not a setting that can be selected.

      Tech Tips

      When either "One Motion" or "One Motion with unlock door" is selected, the other will display "Not Use".

    • *5: The power back door assist operation will be linked with the "Back Door Opening Operation" setting of the entry and start system (for entry function) only when all doors are locked. If "Back Door Opening Operation" is set to "OFF", the power back door assist will not operate even if "PBD Assist Open Operation" is set to "ON" Click here.

    • *6: for models with the "PBD Assist Open Operation" customize setting item.

  24. LIGHTING SYSTEM (LIGHTING EXT)


    1. Customizing with the Intelligent tester

      Light Control
      Display Default Content Setting Relevant ECU
      Response Time*1 Normal Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position. Long / Normal Main Body ECU (Multiplex Network Body ECU)
      Sensitivity Normal Adjusts the sensitivity of the automatic light control system.*A Light2, Light1, Normal, Dark1 or Dark2
      DRL Function On ON/OFF of the DRL function On or Off
      Disp Ex ON Sen Normal Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B Light2, Light1, Normal, Dark1 or Dark2
      Disp Ex OFF Sen Normal Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*C Light2, Light1, Normal, Dark1 or Dark2
      Follow Me Home Lighting Time*2 30 s Sets up the headlight lighting time after the engine switch off. 30 s, 60 s, 90 s or 120 s
      Light up Clearance Lights at Door Unlock Function ON This function turns on the parking lights and the taillights for 15 seconds when the doors are unlocked by the smart key or the wireless key. ON or OFF
      Lane CHG Flash CNT 3 times Changes the lane change flashing times OFF, 3 times, 5 times, 7 times, 9 times or 11 times

      • *1: except European Model

      • *2: for European Model

      Tech Tips

      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

      *A
      Sensitivity of the automatic light control system A019PMI
      Setting Dark2 Dark1 Normal Light1 Light2
      *B
      Brightness level required to dim the lights A019PMI
      Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2
      *C
      Brightness level required to cancel the dimming of the lights A019PMI
      Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2
      Illuminated Entry
      Tester Display Default Content Setting Relevant ECU
      Mirr-Foot-Lgt Approached ON Lights up the door mirror foot lights when a key enters any actuation area around the doors. ON or OFF Main Body ECU (Multiplex Network Body ECU)
      Mirr-Foot-Lgt Unlocked ON Lights up door mirror foot lights when doors are unlocked using a mechanical key or door control transmitter. ON or OFF
      Mirror Foot Lighting Time 15 s Changes the lighting time of the door mirror foot lights. 7.5 s, 15 s, 30 s or 0 s
      Exterior Light Control ON Changes the door mirror foot light control. ON or OFF

    2. Customizing with the Multi-display


      1. Turn the engine switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Lights settings or Other vehicle settings.

      3. Select the setting by referring to the table below.

        Lights settings
        Display Default Content Setting Relevant ECU
        Light sensor sensitivity 0 Adjusts the sensitivity of the automatic light control system.*A -2, -1, 0, +1 or +2 Main Body ECU (Multiplex Network Body ECU)
        Daytime running lights On ON/OFF of the DRL function On or Off
        Exterior lights off timer 15 sec. Changes the lighting time of the door mirror foot lights. Off, 7.5 sec., 15 sec. or 30 sec.
        Other vehicle settings
        Display Default Content Setting Relevant ECU
        Lane change signal flashes 3 Changes the lane change flashing times OFF, 3, 5, 7, 9, or 11 Main Body ECU (Multiplex Network Body ECU)

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

        *A
        Sensitivity of the automatic light control system A019PMI
        Setting -2 -1 0 +1 +2

    3. Customizing using the combination meter assembly

      Tech Tips


      • Press the UP/DOWN switch on the steering pad switch assembly when changing the displayed item and item settings.

      • Press the ENTER switch on the steering pad switch assembly when selecting an item.


      1. Turn the engine switch on (IG).

      2. Press and hold the MENU switch on the steering pad switch assembly.

      3. Select the setting by referring to the table below:

        Display Default Content Setting Relevant ECU
        LIGHT SENSOR SENSITIVITY 0 Adjusts the sensitivity of the automatic light control system.*A -2, -1, 0, +1 or +2 Main Body ECU (Multiplex Network Body ECU)
        DAYTIME RUNNING LIGHTS ON ON/OFF of the DRL function ON or OFF
        EXTERIOR LIGHTS OFF TIME ADJUSTMENT 15 s Changes the lighting time of the door mirror foot lights. OFF, 7.5 s, 15 s or 30 s

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

        *A
        Sensitivity of the automatic light control system A019PMI
        Setting -2 -1 0 +1 +2

      4. Press the ENTER switch on the steering pad switch assembly.

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.