BACK DOOR REASSEMBLY

INSTALL RADIO SETTING CONDENSER

1. 

   Engage the claw to install a new terminal cover to wire harness.

2. 

   Engage the 3 claws to install the new terminal cover with wire harness to a new condenser.

3. Engage the clamp to temporarily install the new radio setting condenser with wire harness to the back door.

4. Install the new radio setting condenser with the bolt.

   8.4 N*m

   86 kgf*cm

   74 in.*lbf

INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

1. 

   Engage the 2 claws to install the antenna cord grommet of back door side.

   Table 1. Text in Illustration

   *1	Clamp
   *2	Grommet

2. Install the antenna cord grommet of vehicle body side.

3. Engage the clamp.

4. Connect the connector.

5. 

   Set the position of the antenna cord grommet of back door side as shown in the illustration.

   Table 2. Text in Illustration

   *1	Grommet Side Match Mark
   *2	Vehicle Body Side Match Mark

6. 

   Set the position of the antenna cord grommet of vehicle body side as shown in the illustration.

   Table 3. Text in Illustration

   *1	Grommet Side Match Mark
   *2	Vehicle Body Side Match Mark

7. Engage the 3 clamps.

8. Engage the 4 clamps and install the No. 3 antenna cord sub-assembly.

INSTALL REAR WASHER NOZZLE

1. 

   Connect the washer hose.

2. 

   Engage the 2 claws to install the rear washer nozzle.

INSPECT REAR WASHER NOZZLE

1. 

   With the engine running, check that the center stream of washer fluid sprays on the windshield within the hatched area shown in the illustration.

   Standard
   Washer fluid hits the windshield in the area shown in the illustration.

   Table 4. Standard Clearance

   Area	Measurement
   A	43 mm (1.693 in.)
   B	50 mm (1.969 in.)
   C	40 mm (1.575 in.)
   D	150 mm (5.906 in.)

   Tip:

   If the result is not as specified, replace the malfunctioning rear washer nozzle.

ADJUST REAR WASHER NOZZLE

1. 

   Using a screwdriver, adjust the direction of the rear washer nozzle.

   Note:

   Do not use a safety pin or other pointed tools. Doing so may damage the inside of the washer nozzle.

   Tip:

   Use a thin-bladed screwdriver with an approximately 1 mm (0.0394 in.) thick tip.

INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY

1. 

   Install the rear wiper motor and bracket assembly with the 3 bolts.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

2. Connect the connector.

3. Engage the clamp.

INSTALL REAR WIPER MOTOR GROMMET

1. 

   Apply MP grease to the entire surface of the rear wiper motor grommet lip.

   Table 5. Text in Illustration

   *1

   MP grease

   Tip:

   Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

2. 

   Install the rear wiper motor grommet.

INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

2. When reusing the rear wiper arm and blade assembly:

   
   
   1. 

      Clean the wiper arm serrations.

      Table 6. Text in Illustration

      *1	Wiper Arm Serrations

3. When reusing the rear wiper motor assembly:

   
   
   1. 

      Clean the wiper pivot serrations with a wire brush.

      Table 7. Text in Illustration

      *1	Wire Brush
      *2	Wiper Pivot Serrations

4. 

   Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

   Table 8. Standard Clearance

   Area	Measurement
   A	30 mm (1.181 in.)

   Table 9. Text in Illustration

   *1	Ceramic Line

   Tip:

   Hold the wiper arm by hand while tightening the nut.

5. Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not come into contact with the vehicle body.

INSTALL REAR SPOILER SUB-ASSEMBLY

1. Install the 2 pins.

2. Install a new clip.

3. 

   Engage the clip and 2 pins to install the rear spoiler sub-assembly.

4. 

   Install the 5 nuts.

   5.9 N*m

   60 kgf*cm

   52 in.*lbf

5. Install the 2 hole plugs.

6. Connect each connector.

INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear Monitor)

1. Install the rear television camera assembly with the bolt and nut.

   10 N*m

   102 kgf*cm

   7 ft.*lbf

2. Connect the connector.

INSTALL LICENSE PLATE LIGHT ASSEMBLY LH

1. 

   Engage the 2 claws to install the license plate light assembly.

2. Connect the connector.

INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

1. Install 2 bolts.

2. Install 2 stud bolts.

3. Install 2 new back door outside garnish clips and 4 new gaskets on the back door outside garnish subassembly.

4. 

   Engage the 2 clips to install the back door outside garnish sub-assembly.

5. Install the 4 nuts.

   4.9 N*m

   50 kgf*cm

   43 in.*lbf

6. Connect each connector.

INSTALL REAR LIGHT ASSEMBLY LH

1. 

   Install the rear light assembly with the 4 nuts.

   5.4 N*m

   55 kgf*cm

   48 in.*lbf

2. Connect each connector.

INSTALL AMPLIFIER ANTENNA ASSEMBLY

1. Engage the 5 clamps.

2. Install the amplifier antenna assembly with the 2 bolts.

   8.0 N*m

   82 kgf*cm

   71 in.*lbf

3. Connect the 3 connectors.

INSTALL BACK DOOR LOWER STAY BRACKET LH

1. Clean the threaded portion on the vehicle body with a non-residue solvent.

2. Apply adhesive to the threads of the 2 bolts.

   Adhesive
   Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

3. 

   Install the back door lower damper stay bracket with the 2 bolts.

   8.0 N*m

   82 kgf*cm

   71 in.*lbf

INSTALL POWER BACK DOOR TOUCH SENSOR ASSEMBLY LH (w/ Power Back Door)

1. 

   Engage the clip.

2. Install the power back door touch sensor assembly with the 4 screws.

   3.5 N*m

   36 kgf*cm

   31 in.*lbf

3. Connect the connector.

INSTALL NO. 2 ROOM LIGHT ASSEMBLY

1. Connect the connector.

2. 

   Engage the claw to install the No. 2 room light assembly.