ROOF HEADLINING REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    w/ Navigation System for HDD:

    After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time after Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A019LA0

      Disengage the 7 claws, 4 clips and guide, and remove the front door scuff plate LH.

      Tech Tips

      A part of the clip remains on the vehicle side.

    2. w/ Illumination:


      1. Disconnect the connector.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A019L27

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. REMOVE INSTRUMENT SIDE PANEL LH


    1. A019N1N

      Using moulding remover A, disengage the claw and 2 clips.

    2. Disengage the guide and remove the instrument side panel LH.

  6. REMOVE FRONT PILLAR GARNISH LH


    1. A019MOHE01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the tips of the needle-nosed pliers before use.

    3. Disengage the 2 guides and remove the front pillar garnish LH.

    4. A019P8ZE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape, as shown in the illustration.

        Protective Cover size
        X
        700 mm (2.30 ft.)
        Y
        120 mm (4.72 in.)

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  7. REMOVE REAR DOOR SCUFF PLATE LH


    1. A019NH1

      Disengage the 6 claws, 3 clips and guide, and remove the rear door scuff plate LH.

  8. REMOVE LOWER CENTER PILLAR GARNISH LH


    1. A019MML

      Disengage the 2 claws and 5 clips, and remove the lower center pillar garnish LH.

  9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A019JMI

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

  10. REMOVE CENTER PILLAR GARNISH LH


    1. A019KIS

      Remove the 2 screws.

    2. Using a clip remover, disengage the clip.

    3. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.

  11. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  12. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  13. REMOVE INSTRUMENT SIDE PANEL RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  14. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  15. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  16. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  17. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  18. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  19. REMOVE DECK BOARD SUB-ASSEMBLY


    1. A019NDK

      Disengage the 3 fasteners as shown in the illustration.

    2. for Compact Spare Tire:


      1. A019N72

        Remove the 2 bolts and remove the deck board sub-assembly.

    3. for Full Size Spare Tire:


      1. A019JPE

        Remove the 2 bolts and remove the deck board sub-assembly.

  20. REMOVE SPARE WHEEL COVER ASSEMBLY (for Compact Spare Tire)


    1. Remove the spare wheel cover assembly.

  21. REMOVE NO. 4 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A019NMY

      Disengage the 2 guides and remove the No. 4 rear floor board.

  22. REMOVE NO. 4 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A019LI6

      Disengage the 2 guides and remove the No. 4 rear floor board.

  23. REMOVE NO. 3 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A019JUH

      Disengage the 2 guides and remove the No. 3 rear floor board.

  24. REMOVE NO. 3 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A019K2O

      Disengage the 2 guides and remove the No. 3 rear floor board.

  25. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  26. REMOVE REAR DECK FLOOR BOX


    1. A019ODU

      Remove the 3 clips and the rear deck floor box.

  27. REMOVE DECK SIDE TRIM BOX LH (for Compact Spare Tire)


    1. A019KNU

      Remove the 2 clips and the deck side trim box LH.

  28. REMOVE DECK SIDE TRIM BOX LH (for Full Size Spare Tire)


    1. A019LL4

      Remove the 3 clips and the deck side trim box LH.

  29. REMOVE DECK SIDE TRIM BOX RH (for Compact Spare Tire)


    1. A019KZM

      Remove the 2 clips and deck side trim box RH.

  30. REMOVE DECK SIDE TRIM BOX RH (for Full Size Spare Tire)


    1. A019LD6

      Remove the 3 clips and the deck side trim box RH.

  31. REMOVE FRONT DECK FLOOR BOX


    1. A019LUJ

      Remove the clip and the front deck floor box.

  32. REMOVE REAR FLOOR FINISH PLATE


    1. A019OZP

      Disengage the 2 claws, 6 clips and 2 guides, and remove the rear floor finish plate.

  33. REMOVE REAR FLOOR FINISH SIDE PLATE LH


    1. A019NQ4

      Remove the clip.

    2. Disengage the claw and 2 clips.

    3. Disengage the guide and remove the rear floor finish side plate LH.

  34. REMOVE REAR SEAT ASSEMBLY LH

    Click here

  35. REMOVE REAR SEAT SIDE COVER LH


    1. A019MJQ

      Remove the 2 clips.

    2. Disengage the 2 claws and 3 clips, and remove the rear seat side cover LH.

      Tech Tips

      A part of the clip remains on the vehicle side.

  36. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)


    1. A019KWU

      Remove the No. 1 luggage compartment trim hook as shown in the illustration.

  37. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    1. A019MHWE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 bolts and the 2 rope hook assemblies.

  38. REMOVE RECLINING REMOTE CONTROL BEZEL LH


    1. A019NFFE01

      Using moulding remover A, disengage the 2 bottom claws of the reclining remote control bezel LH.

    2. Lift the reclining remote control bezel LH as shown by the arrow (1) in the illustration.

    3. Turn the reclining remote control bezel LH as shown by the arrow (2) in the illustration, then disengage the 2 upper claws and remove the bezel.

  39. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 screws.

    2. Remove the 4 clips.

    3. Disengage the 5 claws and 2 clips.

    4. Disconnect each connector and remove the deck trim side panel assembly LH.

      A019P1Z

  40. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A019MP2

      Remove the bolt and disconnect the floor end of the rear seat outer belt assembly.

  41. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Disengage the 8 clips.

      A019P2K

      Tech Tips

      A part of the clip remains on the vehicle side.

    2. Pass the floor anchor of the rear seat outer seat belt assembly LH through the roof side inner garnish assembly LH and remove the roof side inner garnish assembly LH.

  42. REMOVE REAR FLOOR FINISH SIDE PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  43. REMOVE REAR SEAT ASSEMBLY RH

    Click here

  44. REMOVE REAR SEAT SIDE COVER RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  45. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)


    1. A019OIA

      Remove the No. 1 luggage compartment trim hook as shown in the illustration.

  46. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  47. REMOVE RECLINING REMOTE CONTROL BEZEL RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  48. REMOVE HEIGHT CONTROL SWITCH (w/ Air Suspension)


    1. A019KUS

      Disengage the 2 claws to remove the height control switch from the deck trim side panel assembly RH.

    2. Disconnect the connector.

  49. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the 2 screws.

    2. Remove the 5 clips.

    3. Disengage the 5 claws and 2 clips.

    4. Disconnect the connector and remove the deck trim side panel assembly RH.

      A019MNS

  50. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  51. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  52. REMOVE MAP LIGHT ASSEMBLY


    1. w/ Holder:


      1. Open the holder.

    2. w/o Holder:


      1. A019NBAE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver wrapped with protective tape, disengage the 2 claws and disconnect the cover.

    3. A019PKAE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and disconnect the 2 caps.

    4. A019MUU

      Remove the 2 screws.

    5. Using a moulding remover, disengage the 2 clips and 2 guides.

    6. Disconnect each connector and remove the map light assembly.

  53. REMOVE SPOT LIGHT ASSEMBLY


    1. A019LKFE01

      Using a moulding remover, disengage the 2 clips and 2 guides.

    2. Disconnect the connector and remove the spot light assembly.

  54. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. w/o Rear View Monitor System:


      1. A019KUC

        Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

      2. A019KGX

        Disengage the 6 claws and remove the inner rear view mirror stay holder cover.

    2. w/ Rear View Monitor System:


      1. A019KX8

        Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

      2. A019LK5

        Disengage the 2 claws and remove the inner rear view mirror stay holder cover.

  55. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A019KWE

      Disengage the 2 claws and remove the rain sensor cover.

  56. REMOVE COAT HOOK


    1. A019JUJ

      Remove the screw and coat hook.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  57. REMOVE ASSIST GRIP SUB-ASSEMBLY


    1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      A019KXCE01
      Text in Illustration
      *1 Protective Tape

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disengage the 2 clips and remove the assist grip sub-assembly.

      Tech Tips

      Use the same procedure for the other 3 assist grips.

  58. REMOVE VISOR BRACKET COVER (for LH Side)


    1. A019OT0

      Using moulding remover C, disengage the 4 claws and remove the visor bracket cover.

  59. REMOVE VISOR ASSEMBLY LH


    1. A019LXO

      Remove the 2 screws and remove the visor assembly LH.

  60. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  61. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  62. REMOVE VISOR HOLDER (for LH Side)


    1. A019L8GE01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

  63. REMOVE VISOR HOLDER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  64. REMOVE ROOF HEADLINING ASSEMBLY (for Standard Roof)


    1. A019K3P

      Disconnect the No. 2 antenna cord sub-assembly connectors and washer hose, and disengage the 2 claws and 3 clamps from the rear pillar RH.

    2. w/ Rain Sensor:


      1. A019PGO

        Disconnect the No. 1 roof wire connector from the rain sensor.

    3. A019O7K

      Disconnect the No. 1 roof wire connector from the inner rear view mirror.

    4. Disconnect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors and disengage the 2 claws from the front pillar LH.

    5. Disconnect the No. 2 antenna cord sub-assembly connector and washer hose, and disengage the 2 claws from the front pillar RH.

    6. Disconnect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors and disengage the 2 claws from the front pillar LH.

    7. Disengage the 12 claws and 3 clips.

      A019MQJ

    8. Disengage the 2 fasteners.

      A019PF9
    9. A019LTB

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  65. REMOVE ROOF HEADLINING ASSEMBLY (for Sliding roof)


    1. A019K3P

      Disconnect the No. 2 antenna cord sub-assembly connectors and washer hose, and disengage the 2 claws and 3 clamps from the rear pillar RH.

    2. w/ Rain Sensor:


      1. A019PGO

        Disconnect the No. 1 roof wire connector from the rain sensor.

    3. A019O7K

      Disconnect the No. 1 roof wire connector from the inner rear view mirror.

    4. Disconnect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors and disengage the 2 claws from the front pillar LH.

    5. Disconnect the No. 2 antenna cord sub-assembly connector and washer hose, and disengage the 2 claws from the front pillar RH.

    6. Disconnect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors and disengage the 2 claws from the front pillar LH.

    7. Disconnect the No. 1 roof wire connector from the sliding roof drive gear assembly.

    8. Disengage the 12 claws and 3 clips.

      A019MJX

    9. Disengage the 8 fasteners.

      A019NID
    10. A019NVY

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  66. REMOVE ROOF HEADLINING ASSEMBLY (for Glass Roof)


    1. A019K3P

      Disconnect the No. 2 antenna cord sub-assembly connectors and washer hose, and disengage the 2 claws and 3 clamps from the rear pillar RH.

    2. w/ Rain Sensor:


      1. A019PGO

        Disconnect the No. 1 roof wire connector from the rain sensor.

    3. A019O7K

      Disconnect the No. 1 roof wire connector from the inner rear view mirror.

    4. Disconnect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors and disengage the 2 claws from the front pillar LH.

    5. Disconnect the No. 2 antenna cord sub-assembly connector and washer hose, and disengage the 2 claws from the front pillar RH.

    6. Disconnect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors and disengage the 2 claws from the front pillar LH.

    7. Disengage the 12 claws and 3 clips.

      A019MQQ

    8. Disengage the 12 fasteners.

      A019MWE
    9. A019KRY

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  67. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A019KM2

      Remove the front door opening trim weatherstrip LH.

  68. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  69. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A019L4W

      Remove the rear door opening trim weatherstrip LH.

  70. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.