INSTRUMENT PANEL SAFETY PAD INSTALLATION

INSTALL NO. 3 INSTRUMENT PANEL STAY
1. Engage the 5 claws to install the 5 No. 3 instrument panel stays.

INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Engage the 5 claws and temporarily install the instrument panel safety pad assembly as shown in the illustration.

CAUTION:

Leaks of cold air may result in condensation in the instrument panel. This condensation may cause short circuits in electrical parts. Be sure to insert and fit the No. 1 heater to register duct and the No. 4 heater to register duct tightly to the No. 1 air duct sub-assembly.
Note
- Do not damage the instrument panel safety pad assembly.
- Do not allow the wire harnesses to interfere with the surrounding parts.
Install the 2 clips.
Install the 6 bolts <C> and nut <H> or <I>.

Install the 2 passenger airbag bolts <A> or <B>.

Torque:: 20 N*m { 204 kgf*cm, 15 ft.*lbf }

Text in Illustration
*1	Passenger Airbag Bolt <A> or <B>	*2	Bolt <C>
*3	Nut <H> or <I>	*4	Clip
*5	No. 1 Heater To Register Duct	*6	No. 4 Heater To Register Duct
*7	No. 1 Air Duct Sub-assembly	-	-

Engage the 2 claws to connect the room temperature sensor.
Engage each clamp.
Connect each connector.

CONNECT INSTRUMENT PANEL WIRE ASSEMBLY
1. Check that the engine switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Connect the connector.
  
  Note
  
  When connecting the airbag connector, take care not to damage the airbag wire harness.
INSTALL NO. 1 CONSOLE BOX DUCT
1. Install the No. 1 console box duct with the screw <D>.
INSTALL SHIFT LEVER ASSEMBLY

for U660F: Click here

for U760E: Click here
INSTALL NO. 1 DEFROSTER NOZZLE GARNISH
1. Engage the 2 claws to install the automatic light control sensor to the No. 1 defroster nozzle garnish.
2. Connect the connector.
3. Engage the 7 claws and 11 clips to the No. 1 defroster nozzle garnish.
INSTALL FRONT NO. 4 SPEAKER ASSEMBLY
1. Connect the connector.
2. Install the front No. 4 speaker assembly with the 2 bolts.
  
  Torque:
  
  7.5 N*m { 76 kgf*cm, 66 in.*lbf }
INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY
1. Engage the 10 claws and 4 clips to install the No. 1 speaker opening cover assembly.
INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
1. Engage the 4 claws and 3 clips to install the No. 1 instrument panel register assembly.
INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

Tech Tips

Use the same procedure as for the No. 1 instrument panel register assembly.

INSTALL FRONT PILLAR GARNISH LH

Text in Illustration
*1	Adhesive Tape
*2	Protective Cover
*3	Curtain Shield Airbag Assembly

Remove the protective cover.

Make sure that the front pillar garnish clip is not damaged.
Note
- If there is any damage, replace the garnish clip with a new one.
- When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.
Engage the 2 guides.
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

Tech Tips

Tape the tips of the needle-nosed pliers before use.
Engage the 2 clips to install the front pillar garnish LH.

INSTALL INSTRUMENT SIDE PANEL LH
1. Engage the guide.
2. Engage the 2 clips.
3. Engage the claw to install the instrument side panel LH.
INSTALL FRONT PILLAR GARNISH RH

Tech Tips

Use the same procedure as for the LH side Click here.
INSTALL INSTRUMENT SIDE PANEL RH

Tech Tips

Use the same procedure as for the LH side Click here.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
1. Connect each connector.
2. Engage the claw, 4 clips and guide.
3. Install the glove compartment door assembly with the 5 screws <F>.
INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY
1. Check that the engine switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Connect the airbag connector to the front passenger side knee airbag assembly.
  
  Note
  
  When connecting the airbag connector, take care not to damage the airbag wire harness.
4. Temporarily install the front passenger side knee airbag assembly with the claw.
5. Install the front passenger side knee airbag assembly with the 3 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
  
  Note
  
  Confirm that the front passenger side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.
6. Text in Illustration
  
  *1 Protective Tape
  
  Remove the protective tape.
INSTALL INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

Tech Tips

Use the same procedure as for the LH side.
INSTALL INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)
1. Connect the connector.
2. Engage the 6 clips to install the instrument panel garnish RH.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
1. Connect the connector.
2. Engage the 2 guides and 4 claw to install the No. 2 instrument panel under cover sub-assembly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side Click here.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side Click here.
INSTALL CONSOLE BOX (for LHD)
1. Text in Illustration
  
  *1 Clamp
  
  *2 Guide
  
  Engage the 3 guides as shown in the illustration.
2. Engage the 2 clamps.
3. Install the 3 clips.
4. Install the console box with the 5 screws <D>.
INSTALL CONSOLE BOX (for RHD)
1. Text in Illustration
  
  *1 Clamp
  
  *2 Guide
  
  Engage the 3 guides as shown in the illustration.
2. Engage the 2 clamps.
3. Install the 2 clips.
4. Install the console box with the 5 screws <D>.
INSTALL FRONT CONSOLE BOX COVER
1. Connect the connector.
2. Engage the 5 guides and 2 clips, and install the front console box cover.
INSTALL RADIO RECEIVER ASSEMBLY WITH REGISTER (w/o Navigation System)
1. Connect each connector.
2. Engage the 7 clips.
3. Install the radio receiver assembly with register with the 4 bolts.
  
  Torque:
  
  4.9 N*m { 50 kgf*cm, 43 in.*lbf }
INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH REGISTER (w/ Navigation System)
1. Connect each connector.
2. Engage the 7 clips.
3. Install the multi-media module receiver assembly with register with the 4 bolts.
  
  Torque:
  
  4.9 N*m { 50 kgf*cm, 43 in.*lbf }
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
1. Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.
INSTALL INSTRUMENT PANEL FINISH PANEL
1. Engage the 2 guides, claw and 2 clips to install the instrument panel finish panel as shown in the illustration.
INSTALL MULTI-DISPLAY ASSEMBLY (w/ Multi-display)
1. Connect each connector and engage the 2 claws.
2. Install the multi-display assembly with the 3 bolts.
INSTALL ACCESSORY METER ASSEMBLY (w/o Multi-display)
1. Connect each connector.
2. Engage the 2 clips.
3. Install the accessory meter assembly with the 3 screws.
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL
1. Engage the 2 clips as shown in the illustration.
2. Engage the 2 clips and guide to install the center instrument cluster finish panel.
INSTALL COMBINATION METER ASSEMBLY
1. Connect each connector.
2. Install the combination meter assembly with the 2 screws <G>.
INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL
1. Install the 2 screws <E>.
2. Install the No. 1 instrument cluster finish panel with the 2 clips.
INSTALL NO. 1 INSTRUMENT PANEL HOLE COVER
1. Engage the 2 claws to install the No. 1 instrument panel hole cover.
INSTALL NO. 2 INSTRUMENT PANEL HOLE COVER

Tech Tips

Use the same procedure as for the No. 1 instrument panel hole cover.
INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
1. Check that the engine switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Engage the claw to connect the hood lock control cable to the driver side knee airbag assembly.
4. Connect the airbag connector to the driver side knee airbag assembly.
  
  Note
  
  When connecting the airbag connector, take care not to damage the airbag wire harness.
5. Temporarily install the driver side knee airbag assembly with the 2 claws and 2 hooks.
6. Install the driver side knee airbag assembly with the 4 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
  
  Note
  
  Confirm that the driver side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.
INSTALL INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY
1. Install the instrument panel cup holder sub-assembly with the 4 screws <F>.
INSTALL INSTRUMENT PANEL CUP HOLDER OUTER CASE
1. Open the cup holder.
2. Engage the 2 claws.
3. Engage the 2 claws to install the instrument panel cup holder outer case as shown in the illustration.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
1. Connect each connector.
2. Engage the 8 clips and 2 guides.
3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.
4. Engage the 2 claws to close the cover as shown in the illustration.
INSTALL NO. 1 SWITCH HOLE BASE
1. Connect each connector.
2. Engage the 4 claws and 2 guides to install the No. 1 switch hole base.
INSTALL INSTRUMENT PANEL GARNISH LH
1. Engage the 6 clips to install the instrument panel garnish LH.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
1. Engage each clamp.
2. Connect each connector.
3. Engage the claw and 2 guides.
4. Install the No. 1 instrument panel under cover sub- assembly with the 2 screws <D>.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
1. Engage each clamp.
2. Connect each connector.
3. Engage the claw and 2 guides.
4. Install the No. 1 instrument panel under cover sub- assembly with the 2 screws <D>.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
1. Engage the 2 clips to install the cowl side trim sub-assembly LH.
2. Install the clip.
INSTALL FRONT DOOR SCUFF PLATE LH
1. w/ Illumination:
  1. Connect the connector.
2. Engage the 4 clips, guide and 7 claws, and install the front door scuff plate LH.
INSTALL REAR CONSOLE BOX ASSEMBLY
1. Engage the 8 guides as shown in the illustration.
  
  Note
  
  Make sure to install the rear console box assembly in the direction indicated by the arrow (1). Failure to do so will damage the console box and front seat.
2. Install the rear console box assembly with the 2 screws and 4 bolts.
INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY
1. w/o Rear Seat Entertainment System:
  1. Engage the 5 claws and 6 clips to install the console rear end panel sub-assembly.
2. w/ Rear Seat Entertainment System:
  1. Connect each connector.
  2. Engage the 5 claws and 6 clips to install the console rear end panel sub-assembly.
INSTALL NO. 2 CONSOLE BOX DUCT
1. Install the No. 2 console box duct with the 2 screws.
2. Connect each connector and engage the 2 clamps.
INSTALL CONSOLE BOX CUP HOLDER
1. Install the console box cup holder to the console cup holder box sub-assembly as shown in the illustration.
INSTALL CONSOLE CUP HOLDER BOX SUB-ASSEMBLY
1. Install the console cup holder box sub-assembly with the 5 screws <F>.
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
1. Engage the clamp.
2. Connect each connector.
3. Engage the 3 claws and 3 clips.
4. w/o Seat Heater System:
  1. Connect the connector to the console box hole cover.
5. w/ Seat Heater System:
  1. Connect the connector.
  2. Engage the 6 claws to install the seat heater switch with console box hole cover.
6. Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
1. Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.
INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
1. Text in Illustration
  
  *1 Clamp
  
  *2 Claw
  
  Using pliers, expand the clamp.
2. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
3. Return the clamp to its original position.
4. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
INSTALL STEERING COLUMN COVER
1. Engage the claw to install the upper steering column cover.
2. Engage the 2 claws to install the lower steering column cover to the upper steering column cover.
  
  Note
  
  Do not damage the tilt and telescopic switch.
3. Install the 3 screws.
  
  Torque:
  
  2.0 N*m { 20 kgf*cm, 18 in.*lbf }
4. Text in Illustration
  
  *1 Instrument Panel Cluster Finish Panel
  
  Engage the 4 clips and 2 guides to install the instrument panel cluster finish panel to the upper steering column cover.

Text in Illustration
*1	Protective Tape

Text in Illustration
*1	Clamp
*2	Guide

Text in Illustration
*1	Clamp
*2	Guide

Text in Illustration
*1	Clamp
*2	Claw

Text in Illustration
*1	Instrument Panel Cluster Finish Panel

ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Rotate the spiral cable counterclockwise slowly by hand until it stops.

Note

Do not turn the spiral cable using the airbag wire harness.

Text in Illustration
*A	w/o Steering Heater
*B	w/ Steering Heater
*a	Alignment Mark

Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

Note

Do not turn the spiral cable using the airbag wire harness.

Tech Tips

The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

INSTALL STEERING WHEEL ASSEMBLY
1. Text in Illustration
  
  *a Matchmark
  
  Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.
2. Install the steering wheel assembly set nut.
  
  Torque:
  
  50 N*m { 510 kgf*cm, 37 ft.*lbf }
3. w/ Steering Heater:
  1. Connect the connector.
4. Connect each connector to the spiral cable.
INSPECT STEERING WHEEL CENTER POINT
INSTALL STEERING PAD

Click here
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
- Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSPECT SHIFT LEVER POSITION

for U660F: Click here

for U760E: Click here
ADJUST SHIFT LEVER POSITION

for U660F: Click here

for U760E: Click here
INSPECT SUSPENSION CONTROL SYSTEM (w/ Air Suspension)

Click here
INSPECT SRS WARNING LIGHT

Click here