Click here

ROOF HEADLINING REASSEMBLY

Click here
Click here Click here
  1. Click here

    INSTALL NO. 1 ROOF PANEL PAD


    1. A019LXW

      Align the markings on the roof headlining assembly with the No. 1 roof panel pad and install the pad using hot-melt glue or double-sided tape as shown in the illustration.

  2. Click here

    INSTALL NO. 3 ROOF PANEL PAD (w/o Power Back Door)

    Tip:

    Use the same procedure for the RH side and the LH side.

  3. Click here

    INSTALL REAR QUARTER TRIM SILENCER PAD RH


    1. A019OHS

      Align the markings on the roof headlining assembly with the rear quarter trim silencer pad RH and install the silencer pad using hot-melt glue or double-sided tape as shown in the illustration.

  4. Click here

    INSTALL REAR QUARTER TRIM SILENCER PAD LH (w/o Power Back Door)

    Tip:

    Use the same procedure for the RH side and the LH side.

  5. Click here

    INSTALL ROOF HEADLINING FORMING PAD (except Glass Roof)


    1. A019L47

      Align the markings on the roof headlining assembly with the roof headlining forming pad and install the forming pad using hot-melt glue or double-sided tape as shown in the illustration.

  6. Click here

    INSTALL ROOF HEADLINING FORMING PAD (for Glass Roof)


    1. A019LPP

      Align the markings on the roof headlining assembly with the roof headlining forming pad and install the forming pad using hot-melt glue or double-sided tape as shown in the illustration.

  7. Click here

    INSTALL CENTER ROOF HEADLINING PAD


    1. A019OP2

      Align the markings on the roof headlining assembly with the 2 center roof headlining pads and install the pads using hot-melt glue or double-sided tape as shown in the illustration.

  8. Click here

    INSTALL NO. 2 ROOF HEADLINING SET PLATE RH (for Sliding roof)


    1. A019JRN

      Align the markings on the roof headlining assembly with the No. 2 roof headlining set plate RH and install the plate using hot-melt glue or double-sided tape as shown in the illustration.

  9. Click here

    INSTALL NO. 2 ROOF HEADLINING SET PLATE LH (for Sliding roof)

    Tip:

    Use the same procedure for the RH side and the LH side.

  10. Click here

    INSTALL ROOF HEADLINING SET PLATE RH (for Sliding roof)


    1. A019PK4

      Align the markings on the roof headlining assembly with the roof headlining set plate RH and install the plate using hot-melt glue or double-sided tape as shown in the illustration.

  11. Click here

    INSTALL ROOF HEADLINING SET PLATE LH (for Sliding roof)

    Tip:

    Use the same procedure for the RH side and the LH side.

  12. Click here

    INSTALL ROOF HEADLINING PAD LH (except Glass Roof)


    1. w/o Power Back Door:


      1. A019PDM

        Align the markings on the roof headlining assembly with the roof headlining pad LH and install the pad using hot-melt glue or double-sided tape as shown in the illustration.

    2. w/ Power Back Door:


      1. A019LG3

        Align the markings on the roof headlining assembly with the roof headlining pad LH and install the pad using hot-melt glue or double-sided tape as shown in the illustration.

  13. Click here

    INSTALL ROOF HEADLINING PAD RH (except Glass Roof)


    1. A019OSF

      Align the markings on the roof headlining assembly with the roof headlining pad RH and install the pad using hot-melt glue or double-sided tape as shown in the illustration.

  14. Click here

    INSTALL REAR SIDE RAIL SPACER RH (for Standard Roof)


    1. A019PI8

      Align the markings on the roof headlining assembly with the rear side rail spacer RH and install the spacer using hot-melt glue or double-sided tape as shown in the illustration.

  15. Click here

    INSTALL REAR SIDE RAIL SPACER LH (for Standard Roof)

    Tip:

    Use the same procedure for the RH side and the LH side.

  16. Click here

    INSTALL FRONT SIDE RAIL SPACER RH (for Standard Roof)


    1. A019JOG

      Align the markings on the roof headlining assembly with the front side rail spacer RH and install the spacer using hot-melt glue or double-sided tape as shown in the illustration.

  17. Click here

    INSTALL FRONT SIDE RAIL SPACER LH (for Standard Roof)

    Tip:

    Use the same procedure for the RH side and the LH side.

  18. Click here

    INSTALL FRONT ROOF HEADLINING SIDE PAD (except Glass Roof)


    1. A019NHX

      Align the markings on the roof headlining assembly with the 2 front roof headlining side pads and install the pads using hot-melt glue or double-sided tape as shown in the illustration.

  19. Click here

    INSTALL FRONT ROOF HEADLINING SIDE PAD (for Glass Roof)


    1. A019JRD

      Align the markings on the roof headlining assembly with the 2 front roof headlining side pads and install the pads using hot-melt glue or double-sided tape as shown in the illustration.

  20. Click here

    INSTALL ROOF HEADLINING PAD (except Glass Roof)


    1. A019KPQE01

      Align the markings on the roof headlining assembly with the roof headlining pad and install the pad using hot-melt glue or double-sided tape as shown in the illustration.

  21. Click here

    INSTALL ROOF HEADLINING PAD (for Glass Roof)


    1. A019M96

      Align the markings on the roof headlining assembly with the roof headlining pad and install the pad using hot-melt glue or double-sided tape as shown in the illustration.

  22. Click here

    INSTALL ROOF HEADLINING SPACER (except Glass Roof)


    1. A019NF5

      Align the markings on the roof headlining assembly with the roof headlining spacer and install the spacer using hot-melt glue or double-sided tape as shown in the illustration.

  23. Click here

    INSTALL NO. 3 ROOF SILENCER


    1. A019P97

      Align the markings on the roof headlining assembly with the No. 3 roof silencer and install the silencer using hot-melt glue or double-sided tape as shown in the illustration.

  24. Click here

    INSTALL NO. 2 ROOF SILENCER (for Standard Roof)


    1. A019KJW

      Align the markings on the roof headlining assembly with the 3 No. 2 roof silencers and install the silencers using hot-melt glue or double-sided tape as shown in the illustration.

  25. Click here

    INSTALL NO. 2 ROOF SILENCER (for Sliding roof)


    1. A019NSA

      Align the markings on the roof headlining assembly with the No. 2 roof silencer and install the silencer using hot-melt glue or double-sided tape as shown in the illustration.

  26. Click here

    INSTALL NO. 2 ROOF SILENCER (for Glass Roof)


    1. A019P5G

      Align the markings on the roof headlining assembly with the No. 2 roof silencer and install the silencer using hot-melt glue or double-sided tape as shown in the illustration.

  27. Click here

    INSTALL CENTER ROOF SILENCER PAD (for Standard Roof)


    1. A019NU7

      Align the markings on the roof headlining assembly with the center roof silencer pad and install the silencer pad using hot-melt glue or double-sided tape as shown in the illustration.

  28. Click here

    INSTALL SUNSHADE TRIM PROTECTOR (for Standard Roof)


    1. Install 2 new sunshade trim protectors.


      1. Remove the release paper from the 2 sunshade trim protectors.

        Tip:

        After removing the release paper, keep the exposed adhesive free from foreign matter.

      2. A019PKI

        Align the markings on the roof headlining assembly with the 2 sunshade trim protectors and install the 2 protectors as shown in the illustration.

  29. Click here

    INSTALL NO. 2 HOOK FASTENER (for Sliding roof)


    1. A019NTV

      Align the markings on the roof headlining assembly with the 2 No. 2 hook fasteners and install the fastener using hot-melt glue as shown in the illustration.

  30. Click here

    INSTALL NO. 1 HOOK FASTENER (for Sliding roof)


    1. A019MV2

      Align the markings on the roof headlining assembly with the 2 No. 1 hook fasteners and install the fastener using hot-melt glue as shown in the illustration.

  31. Click here

    INSTALL NO. 1 ROOF WIRE


    1. Apply new double-sided tape.


      1. Remove the double-sided tape from the roof headlining assembly.

      2. Peel off the appropriate amount of new double sided tape.

        Area Dimension
        X 1.0 mm (0.0394 in.)
        Y 15.0 mm (0.591 in.)
        Note:

        Be careful not to touch the adhesive surface.

      3. Apply the double sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

      4. Peel off the backing sheet from the double sided tape.

    2. Install the No. 1 roof wire to the roof headlining assembly.

      Tip:

      • For the left front corner <A> of the roof headlining assembly, align the marking tape (white) on the No. 1 roof wire with the protrusion of the roof headlining.

      • Align the markings on the roof headlining assembly with the joint box.

    3. A019M07E01

      Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining assembly.

      Table 1. Text in Illustration
      *1 Double Sided Tape Area *2 Marking Tape
      *3 Joint Box - -
    4. A019MI9E01

      Apply adhesive tape to the locations shown in the illustration.

      Table 2. Text in Illustration
      *1 Adhesive Tape
      Tip:

      As shown in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

  32. Click here

    INSTALL REAR NO. 3 WASHER HOSE

    Tip:

    The double-sided tape is not available as supply parts. If the tape still has enough adhesion to secure the roof headlining and rear No. 3 washer hose, reuse the tape. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.


    1. Apply new double-sided tape.


      1. Remove the double-sided tape from the roof headlining assembly.

      2. Peel off the appropriate amount of new double sided tape.

        Area Dimension
        X 1.0 mm (0.0394 in.)
        Y 15.0 mm (0.591 in.)
        Note:

        Be careful not to touch the adhesive surface.

      3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

      4. Peel off the backing sheet from the double sided tape.

    2. A019LJFE01

      Install the rear No. 3 washer hose to the roof headlining assembly from the front of the vehicle.

      Table 3. Text in Illustration
      *1 Double Sided Tape Area *2 Marking Tape
      *3 Adjustment Area - -
      Tip:

      • For the right front corner <A> of the roof headlining assembly, align the marking tape (green) on the rear No. 3 washer hose with the protrusion of the roof headlining.

      • For the right rear corner <B> of the roof headlining assembly, align the marking tape (green) on the rear No. 3 washer hose with the marking of the roof headlining.

      • If the entire length of the rear No. 3 washer hose does not fit, adjust the length by tucking in the hose at the area shown in the illustration.

  33. Click here

    INSTALL NO. 5 ANTENNA CORD SUB-ASSEMBLY

    Tip:

    Double-sided tape and tape are not available as supply parts. If the tape still has enough adhesion to secure the roof headlining and antenna cord, reuse it. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.

    If the double-sided tape cannot be reused:


    1. Peel off the release paper from one side of new double-sided tape and apply the new double-sided tape to the position indicated in the illustration. Be careful not to touch the adhesive surface.

      Note:

      Be sure to apply the double-sided tape carefully so that the tape will not be misaligned or come off.

    2. A019M7TE02

      Peel off the release paper from the double-sided tape. Be careful not to touch the adhesive surface.

      Table 4. Text in Illustration
      *A for Standard Roof *B for Sliding Roof
      *C for Glass Roof - -
      *1 Double-sided Tape - -
      *a Front *b Double-sided Tape Size
      Table 5. Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 15.0 mm (0.591 in.)

    3. Align the vehicle front side marking (yellow) on the No. 5 antenna cord sub-assembly with the vehicle front side tab on the roof headlining, and wrap the tape over the antenna cord to install it. (A)

      Tip:

      If the tape cannot be reused, packing tape can be used as a substitute.

    4. Temporarily install the No. 5 antenna cord sub-assembly by placing it on the double-sided tape from the front of the vehicle to the point just before the extra cord storage area.

    5. Align the vehicle rear marking (yellow) on the No. 5 antenna cord sub-assembly with the tape attachment location (scribe line) of the roof headlining, and wrap the tape over the antenna cord to install it. (B)

      Tip:

      If the tape cannot be reused, packing tape can be used as a substitute.

    6. Temporarily install the No. 5 antenna cord sub-assembly by placing it on the double-sided tape from the rear of the vehicle to the point just before the extra cord storage area.

    7. A019MHRE02

      Using double-sided tape, place any excess No. 5 antenna cord sub-assembly in the extra cord storage area to finish installing the antenna cord.

      Tip:

      Attach 3 pieces of double-sided tape to the extra cord storage area as shown in the illustration.

      Table 6. Text in Illustration
      *A for Standard Roof *B for Sliding Roof
      *C for Glass Roof - -
      *1 Double-sided Tape *2 Adhesive Tape
      *3 Marking (Yellow) - -
      *a Front *b Double-sided Tape Size
      *c Extra Cord Storage Area - -
      Table 7. Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 15.0 mm (0.591 in.)
  34. Click here

    INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Tip:

    Double-sided tape and tape are not available as supply parts. If the tape still has enough adhesion to secure the roof headlining and antenna cord, reuse it. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.

    If the double-sided tape cannot be reused:


    1. A019L7FE02

      Peel off the release paper from one side of new double-sided tape and apply the new double-sided tape to the position indicated in the illustration. Be careful not to touch the adhesive surface.

      Table 8. Text in Illustration
      *A for Standard Roof *B for Sliding Roof
      *C for Glass Roof - -
      *1 Double-sided Tape - -
      *a Front *b Double-sided Tape Size
      Table 9. Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 15.0 mm (0.591 in.)
      Note:

      Be sure to apply the double-sided tape carefully so that the tape will not be misaligned or come off.

    2. Peel off the release paper from the double-sided tape. Be careful not to touch the adhesive surface.

    3. Align the vehicle front side marking (yellow) on the No. 2 antenna cord sub-assembly with the vehicle front side tab on the roof headlining, and wrap the tape over the antenna cord to install it. (A)

      Tip:

      If the tape cannot be reused, packing tape can be used as a substitute.

    4. Temporarily install the No. 2 antenna cord subassembly by placing it on the double-sided tape from the front of the vehicle to the point just before the extra cord storage area.

    5. Align the vehicle rear marking (yellow) on the No. 2 antenna cord sub-assembly with the tape attachment location (scribe line) of the roof headlining, and wrap the tape over the antenna cord to install it. (B)

      Tip:

      If the tape cannot be reused, packing tape can be used as a substitute.

    6. Temporarily install the No. 2 antenna cord subassembly by placing it on the double-sided tape from the rear of the vehicle to the point just before the extra cord storage area.

    7. A019LI2E02

      Using double-sided tape, place any excess No. 2 antenna cord sub-assembly in the extra cord storage area to finish installing the antenna cord.

      Tip:

      Attach 3 pieces of double-sided tape to the extra cord storage area as shown in the illustration.

      Table 10. Text in Illustration
      *A for Standard Roof *B for Sliding Roof
      *C for Glass Roof - -
      *1 Double-sided Tape *2 Adhesive Tape
      *3 Marking (Yellow) - -
      *a Front *b Double-sided Tape Size
      *c Extra Cord Storage Area - -
      Table 11. Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 15.0 mm (0.591 in.)
  35. Click here

    INSTALL VANITY LIGHT ASSEMBLY


    1. Install the vanity light assembly (Click here)

      Tip:

      Use the same procedure to remove the light on the other side.