LUMBAR SWITCH INSTALLATION


  1. INSTALL LUMBAR SWITCH


    1. A019ORL

      Install the lumbar switch to the front cushion shield with the 2 screws.

  2. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. w/ Seat Cushion Front Edge Adjustment Function:


      1. A019KCL

        Connect the connector.

      2. Engage the 2 clamps to the install the seat wire to front seat cushion shield assembly with seat variable cushion switch.

    2. A019LBE

      Connect the connector to the lumbar switch.

    3. A019NLO

      Engage the guide and claw.

    4. Install the front seat cushion shield assembly with the 5 screws.

    5. A019K8L

      Engage the 2 hooks and install the 2 rubber bands of the front seatback board to the seat frame.

  3. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A019OZE

      Engage the 4 claws and install the slide and vertical power seat switch knob.

  4. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A019P8G

      Engage the 4 claws and install the reclining power seat switch knob.

  5. INSTALL FRONT SEAT ASSEMBLY


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connectors under the seat.

    3. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Operate the power seat switch knob and move the seat to the rearmost position.

    6. A019KOEE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      37 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    7. Operate the power seat switch knob and move the seat to the foremost position.

    8. A019OSZE01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      37 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  6. INSTALL REAR INNER SEAT TRACK BRACKET COVER


    1. A019JL4

      Engage the 4 claws and install the rear inner seat track bracket cover as shown in the illustration.

  7. INSTALL REAR OUTER SEAT TRACK BRACKET COVER


    1. A019KR5

      Engage the 4 claws to install the rear outer seat track bracket cover as shown in the illustration.

  8. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A019OWA

      Engage the 2 guides and 2 claws to install the front inner seat track bracket cover as shown in the illustration.

  9. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. A019LK1

      Engage the 2 guides and 2 claws to install the front outer seat track bracket cover as shown in the illustration.

  10. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. A019JWX

      Install the front seat headrest assembly as shown in the illustration.

  11. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation.

    2. Check the seat heater operation.

      w/o Climate Control Seat System:


      1. Turn the engine switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

  12. INSPECT SRS WARNING LIGHT

    Click here