LUMBAR SWITCH REMOVAL


  1. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. A019O82

      Press the headrest support button and pull up the headrest as shown in the illustration to remove it.

  2. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A019NLG

      Disengage the 2 claws and 2 guides, and remove the front outer seat track bracket cover as shown in the illustration.

  3. REMOVE FRONT INNER SEAT TRACK BRACKET COVER


    1. A019LY7

      Disengage the 2 claws and 2 guides, and remove the front inner seat track bracket cover as shown in the illustration.

  4. REMOVE REAR OUTER SEAT TRACK BRACKET COVER


    1. A019NBG

      Disengage the 4 claws and remove the rear outer seat track bracket cover as shown in the illustration.

  5. REMOVE REAR INNER SEAT TRACK BRACKET COVER


    1. A019LZ9

      Disengage the 4 claws and remove the rear inner seat track bracket cover as shown in the illustration.

  6. REMOVE FRONT SEAT ASSEMBLY


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A019OSZ

      Remove the 2 bolts on the rear side of the seat.

    3. Operate the power seat switch knob and move the seat to the rearmost position.

    4. A019KOE

      Remove the 2 bolts on the front side of the seat.

    5. Operate the power seat switch knob and move the seat to the center position. Also, operate the power seat switch knob and move the seatback to the upright position.

    6. w/ Navigation System for HDD:

      Note

      After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

    7. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    8. Disconnect the connectors under the seat.

    9. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A019KY1

      Using a moulding remover, disengage the 4 claws and remove the reclining power seat switch knob.

  8. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A019L87

      Using a moulding remover, disengage the 2 claws as shown in the illustration.

    2. A019LJJ

      Using a moulding remover, disengage the 2 claws and remove the slide and vertical power seat switch knob.

  9. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. A019K8L

      Disengage the 2 hooks and remove the 2 rubber bands of the front seatback board from the front seat frame.

    2. A019NLO

      Remove the 5 screws.

    3. Disengage the claw and guide.

    4. Disconnect the connector from the front power seat lumbar switch.

    5. w/ Seat Cushion Front Edge Adjustment Function:


      1. A019KCL

        Disengage the 2 clamps.

      2. Disconnect the connector from the seat variable cushion switch.

    6. Remove the front seat cushion shield assembly.

  10. REMOVE LUMBAR SWITCH


    1. A019ORL

      Remove the 2 screws and lumbar switch.