REAR SEAT ASSEMBLY (for LH Side) REASSEMBLY


  1. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY LH


    1. A019OWL

      Using a T45 "TORX" socket wrench, install the rear seat cushion spring assembly LH with the 4 bolts and 4 bushes.

      Torque:
      21 N*m  { 214 kgf*cm, 16 ft.*lbf }

  2. INSTALL NO. 2 REAR SEAT RECLINING CONTROL CABLE


    1. A019KBS

      Engage the claw to install the rear seat hook.

    2. Engage the 4 rear seat hooks.

    3. Engage the 6 cable clamps and install the No. 2 rear seat reclining control cable.

      A019M1Z

  3. INSTALL REAR SEAT RECLINING INNER COVER LH


    1. A019KJ3

      Engage the 2 claws.

    2. Install the rear seat reclining inner cover LH with the screw.

  4. INSTALL REAR SEAT CUSHION SIDE COVER LH


    1. A019MKM

      Engage the claw.

    2. Install the rear seat cushion side cover LH with the 2 screws.

  5. INSTALL NO. 2 REAR SEAT INNER SHIELD COVER


    1. A019P6B

      Engage the claw.

    2. Install the No. 2 rear seat inner shield cover with the 2 screws.

  6. INSTALL NO. 3 REAR SEAT COVER


    1. A019KRE

      Install the No. 3 rear seat cover with the screw.

  7. INSTALL SEPARATE TYPE REAR SEATBACK COVER


    1. A019K4D

      Using hog ring pliers, install the separate type rear seatback cover with 12 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A019N4P

      As shown in the illustration, pass the bracket of the separate type rear seatback cover through the separate type rear seatback pad.

      Note

      After installing the bracket, check that the band is not twisted.

  8. INSTALL REAR SEATBACK COVER WITH PAD


    1. A019JNDE01
      Text in Illustration
      *1 Side Airbag

      Temporarily install the side airbag so that it is stored inside the rear seatback cover with pad.

      Note

      Make sure that the side airbag is stored inside the pad correctly. Otherwise the side airbag may not deploy properly.

    2. Install bracket A onto the bolt and insert the guide.

      A019NCJE01
      Text in Illustration
      *1 Bracket A *2 Bracket B

    3. Install bracket B onto the bolt and insert the guide.

    4. Install the rear seatback cover bracket with the nut.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }

      Note


      • For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.

      • Check that the strap is not twisted after installing the bracket.

      • Install the bracket securely.

    5. A019PJG

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    6. Install the 2 hooks.

    7. A019L6Y

      Install the rear seat belt hook with the bolt.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }
    8. A019JST

      Using hog ring pliers, install 4 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    9. Engage the 5 hooks to install the rear seatback cover with pad.

    10. A019MHCE01
      Text in Illustration
      *1 Fastener

      Engage 2 fasteners.

  9. INSTALL REAR SEAT HEADREST SUPPORT RH


    1. A019PF3

      Engage the 2 claws to install the rear seat headrest support RH.

  10. INSTALL REAR SEAT HEADREST SUPPORT LH


    1. A019MJL

      Engage the 2 claws to install the rear seat headrest support LH.

  11. INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY


    1. A019O0Q

      Engage the guide.

    2. Install the No. 1 fold seat stopper band assembly with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  12. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH


    1. A019KLL

      Engage the guide.

    2. Engage the 2 clips to install the rear seatback board carpet assembly LH.

  13. INSTALL REAR SEATBACK COVER


    1. A019OR8

      Engage the 4 claws to install the rear seatback cover.

  14. INSTALL TONNEAU COVER HOOK HOLDER


    1. A019PBZ

      Engage the 2 guides.

    2. Install the 2 tonneau cover hook holders with the 2 screws.

  15. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER


    1. A019PKB

      Using hog ring pliers, install the separate type rear seat cushion cover with 11 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  16. INSTALL REAR SEAT INNER BELT ASSEMBLY LH


    1. Install the rear sear inner belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  17. INSTALL REAR SEAT CUSHION COVER WITH PAD


    1. A019MUK

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A019PJ3

      Engage the 2 hooks.

    3. A019JUP

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    4. Engage each hook as shown in the illustration.

      A019K0M
    5. A019OXS

      Engage the 2 elastic bands to install the rear seat cushion cover with pad.

  18. INSTALL REAR SEAT CUSHION MOULDING RH


    1. A019PJL

      Engage the 4 claws.

    2. Install the rear seat cushion moulding RH with the 3 screws.

  19. INSTALL REAR SEAT CUSHION MOULDING LH


    1. A019M81

      Engage the guide as shown in the illustration.

    2. A019P1Y

      Engage the 2 guides.

    3. Install the rear seat cushion moulding LH with the 2 screws.

  20. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH


    1. A019KZL

      Install the No. 1 reclining adjuster release handle LH with the 3 screws.

  21. INSTALL REAR SEAT COVER CAP


    1. A019KVH

      Engage the 3 claws to install the rear seat cover cap.

  22. INSTALL REAR CENTER INNER BELT ASSEMBLY LH


    1. Install the rear center seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }