FRONT SEAT ASSEMBLY REASSEMBLY


  1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

    CAUTION:


    • The nuts must not be reused.

    • Make sure that the front seat frame assembly with adjuster is not deformed. If it is, replace it with a new one.


    1. A019MVN

      Install the front seat side airbag assembly with 2 new nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A019P8R

      Engage the 2 clamps.

    3. A019NHJ

      Engage the 3 clamps to install the wire harness.

  2. INSTALL FRONT SEAT WIRE


    1. A019NK0

      Engage the 8 clamps and install the front seat wire to the front seat frame assembly with adjuster.

    2. Connect the 3 connectors.

    3. A019MET

      Engage the 3 clamps and install the front seat wire.

    4. Connect the connector.

    5. w/ Rear Seat Entertainment System:


      1. A019MBQ

        Engage the 5 clamps.

  3. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Climate Control Seat System)


    1. A019KMM

      Engage the 2 guides and install the seat heater control sub-assembly.

    2. Connect the connector.

  4. INSTALL SEAT POSITION SENSOR


    1. A019JLZ

      Install the seat position sensor to the seat slide position sensor protector with the pin as shown in the illustration.

    2. A019MOME12
      Text in Illustration
      *1 Seat Position Sensor
      *2 Feeler Gauge
      *3 Seat Rail

      Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position sensor.

      Note


      • If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.

      • When installing the seat position sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    3. A019O9P

      Using a T30 "TORX" socket wrench, tighten the "TORX" screw to install the seat position sensor.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Make sure that the clearance between the seat position sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    5. Connect the connector.

    6. Check that there is no looseness in the installation parts of the seat position sensor.

  5. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. A019MEQ

      Engage the 2 hooks and temporarily install the seat cushion climate control blower.

    2. Install the screw.

    3. Connect the connector and install the seat cushion climate control blower as shown in the illustration.

  6. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)


    1. A019K7RE02

      Engage the 2 claws.

    2. Engage the 2 clamps (A) in the direction indicated by the arrow.

    3. Engage the 2 clamps (B) in the direction indicated by the arrow and install the seat cushion climate control duct.

  7. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    1. A019MQ5E01
      Text in Illustration
      *1 Hook
      *2 Guide

      Engage the guide.

    2. Engage the hook as shown in the illustration.

    3. Install the front seat lower cushion shield RH with the screw.

  8. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    1. A019NVBE02
      Text in Illustration
      *1 Hook
      *2 Guide

      Engage the guide.

    2. Engage the hook as shown in the illustration.

    3. Install the front seat lower cushion shield LH with the screw.

  9. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH


    1. A019ON0

      Engage the guide.

    2. Install the upper reclining adjuster inside cover RH with the screw.

  10. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH


    1. A019MFLE02
      Text in Illustration
      *1 Guide
      *2 Clamp

      Engage the guide.

    2. Engage the clamp and install the side airbag wire harness.

    3. Install the lower reclining adjuster inside cover RH with the 2 screws.

  11. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH


    1. A019JWE

      Engage the guide.

    2. Install the upper reclining adjuster inside cover LH with the screw.

  12. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH


    1. A019MC5E02
      Text in Illustration
      *1 Guide
      *2 Clamp

      Engage the guide.

    2. Install the lower reclining adjuster inside cover LH with the 2 screws.

    3. Engage the clamp and install the side airbag wire harness.

  13. INSTALL ACTIVE HEADREST LOWER UNIT


    1. A019OG1

      Install the active headrest lower unit with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  14. INSTALL ACTIVE HEADREST UPPER UNIT


    1. A019MFGE01

      Install the active headrest upper unit with the 4 nuts <B>.

      Torque:
      14 N*m  { 134 kgf*cm, 10 ft.*lbf }

    2. Connect the cable to the active headrest upper unit with the nut <A> as shown in the illustration.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  15. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY


    1. A019N39

      Install the bush.

    2. A019NGU

      Engage the guide.

    3. Install the lumbar support adjuster assembly with the 2 screws.

    4. Connect the connector.

    5. A019NNT

      Engage the 2 clamps as shown in the illustration.

    6. A019O99

      Engage the 4 guides and install the front seatback spring sub-assembly.

    7. A019MVQ

      Engage the 4 guides to install the seatback felt.

  16. INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. A019NR1

      Using a T30 ''TORX'' socket, install the seatback climate control blower and the seatback climate control cover to the seat frame with the 6 ''TORX'' bolts.

      Torque:
      2.6 N*m  { 27 kgf*cm, 23 in.*lbf }

    2. for Driver Side:


      1. A019LKZ

        Engage the 3 clamps and install the wire harness.

      2. Connect the connector.

    3. for Front Passenger Side:


      1. A019LB5

        Engage the clamp and install the wire harness.

      2. Connect the connector.

  17. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Climate Control Seat System)


    1. A019NN2

      Using a tacker, install the front seatback heater assembly to the end of the seat cover with the 12 tack pins.

      Note


      • Be careful not to damage the cover.

      • When installing the tack pins, take care to minimize wrinkles as much as possible.

  18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A019M1M

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 14 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  19. INSTALL FRONT SEATBACK COVER WITH PAD


    1. A019MJHE01
      Text in Illustration
      *1 Side Airbag

      Temporarily install the side airbag so that it is stored inside the separate type front seatback cover with pad.

      Note

      Make sure that the side airbag is stored inside the pad correctly. Otherwise the side airbag may not deploy properly.

    2. Install bracket A onto the bolt.

      A019LXCE01
      Text in Illustration
      *1 Bracket A *2 Bracket B

    3. Install bracket B onto the bolt and insert the guide.

    4. Install the front seatback cover bracket with the nut.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }

      CAUTION:


      • For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.

      • Make sure that the strap is not twisted after installing the bracket.

      • Install the bracket securely.

    5. A019LLC

      Engage the 6 hooks as shown in the illustration.

    6. A019L28

      Using hog ring pliers, install the seatback cover to the seat frame with 5 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    7. A019NYZ

      Engage the 2 hooks and install the front seatback cover with pad.

  20. INSTALL FRONT SEAT HEADREST SUPPORT


    1. A019OYX

      Engage the 4 claws and install the 2 front seat headrest supports.

  21. INSTALL FRONT SEATBACK BOARD COVER SUB-ASSEMBLY


    1. A019KI1

      Engage the 2 hooks to install the front seatback board cover sub-assembly.

  22. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY


    1. A019OQG

      Engage the 2 guides as shown in the illustration.

    2. A019LFS

      Install the front setback board sub-assembly with the 2 screws.

  23. INSTALL NO. 2 TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. A019KBU

      Engage the 2 guides.

    2. Install the 5 clips.

    3. A019M86

      Install the No. 2 television base with the 4 screws.

  24. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)


    1. Install the television display assembly with the 3 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the connector.

  25. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. Engage the 3 guides and 3 claws to install the television base.

  26. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Climate Control Seat System)


    1. A019PJQ

      Using a tacker, install the front seat cushion heater assembly to the end of the seat cover with the 30 tack pins.

      Note


      • Be careful not to damage the cover.

      • When installing the tack pins, take care to minimize wrinkles as much as possible.

  27. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function)


    1. A019KIJ

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 19 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A019NSJ

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  28. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function)


    1. A019NNY

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A019NSJ

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  29. INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function)


    1. w/o Climate Control Seat System:


      1. A019LAD

        Engage the 5 clamps.

    2. w/ Climate Control Seat System:


      1. A019NGQ

        Engage the 6 clamps.

      2. Connect the 2 connectors.

    3. for Front Passenger Side:


      1. A019LHQ

        Engage the 2 clamps and connect the occupant detection sensor connector.

    4. Engage each hook as shown in the illustration.

      A019LBI

    5. Install the 2 clips.

    6. A019NWJ

      Engage the 6 hooks and install the front seat cushion cover with pad.

  30. INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function)


    1. A019OSO

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A019LSQ

      Engage the 4 hooks.

    3. Engage each hook as shown in the illustration.

      A019NLA

    4. for Front Passenger Side:


      1. A019LHQ

        Engage the 2 clamps and connect the occupant detection sensor connector.

    5. Install the 2 clips.

    6. A019NWJ

      Engage the 6 hooks and install the front seat cushion cover with pad.

  31. INSTALL POWER SEAT SWITCH


    1. A019LS6

      Connect the 2 connectors.

    2. A019PJS

      Engage the guide.

    3. Install the power seat switch with the 3 screws.

  32. INSTALL FRONT SEAT CUSHION INNER SHIELD


    1. A019O3R

      Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.

    2. A019KFH

      Engage the claw.

    3. Install the front seat cushion inner shield with the screw.

  33. INSTALL SEAT VARIABLE CUSHION SWITCH (w/ Seat Cushion Front Edge Adjustment Function)


    1. A019MNI

      Install the seat variable cushion switch with the 2 screws.

  34. INSTALL LUMBAR SWITCH


    1. A019ORL

      Install the lumbar switch with the 2 screws.

  35. INSTALL NO. 1 FRONT SEAT CUSHION INNER SHIELD


    1. A019M91

      Engage the 2 guides as shown in the illustration.

    2. Install the No. 1 front seat cushion inner shield with the 2 screws.

  36. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. w/ Seat Cushion Front Edge Adjustment Function:


      1. A019KCL

        Connect the connector.

      2. Engage the 2 clamps to the install the seat wire to front seat cushion shield assembly with seat variable cushion switch.

    2. A019LBE

      Connect the connector to the lumbar switch.

    3. A019NLO

      Engage the guide and claw.

    4. Install the front seat cushion shield assembly with the 5 screws.

    5. A019K8L

      Engage the 2 hooks and install the 2 rubber bands of the front seatback board to the seat frame.

  37. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A019OZE

      Engage the 4 claws and install the slide and vertical power seat switch knob.

  38. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A019P8G

      Engage the 4 claws and install the reclining power seat switch knob.

  39. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    1. A019M8KE01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of front seat adjuster.

    2. Connect each connector and clamp.