ВПУСКНОЙ КОЛЛЕКТОР СНЯТИЕ


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A01FTR0

      Освободите 4 фиксатора и снимите боковую крышку моторного отсека.

  2. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01FS00

      Снимите 7 фиксаторов и сальник впускного воздухопровода холодного воздуха.

  3. REMOVE NO. 1 AIR CLEANER INLET


    1. A01FUV7

      Выверните болт и снимите входной патрубок воздушного фильтра № 1.

  4. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

    Click here

  5. REMOVE INJECTOR DRIVER

    Click here

  6. DISCONNECT INVERTER RESERVE TANK ASSEMBLY (for RHD)


    1. A01FQA7

      Remove the 2 bolts and inverter reserve tank assembly from the No. 1 inverter reserve tank bracket.

  7. REMOVE VACUUM SENSOR ASSEMBLY


    1. A01FRNZ

      Disconnect the vacuum sensor assembly connector.

    2. Remove the bolt and vacuum sensor assembly from the intake manifold.

  8. REMOVE PURGE VSV


    1. A01FRUG

      Disconnect the purge VSV connector.

    2. Disconnect the No. 2 fuel vapor feed hose from the purge VSV.

    3. Slide the clip and disconnect the No. 2 fuel vapor feed hose from the purge VSV.

    4. A01FQXI

      Remove the bolt and purge VSV from the wire harness clamp bracket.

  9. DISCONNECT INLET HEATER WATER HOSE A


    1. С помощью плоскогубцев зажмите захваты фиксатора и сдвиньте фиксатор.

    2. Отсоедините входной патрубок A отопителя.

  10. REMOVE OUTLET HEATER WATER HOSE A


    1. Slide the hose clamp, and disconnect the outlet heater water hose A from the heater unit.

    2. A01FRU7

      Remove the water hose set from the outlet heater water hose A.

    3. A01FS7J

      Slide the hose clamp, and remove the No. 2 water by-pass pipe from the No. 2 water by-pass pipe.

  11. REMOVE NO. 2 EGR PIPE (w/ EGR System)


    1. A01FQC9

      Remove the 2 bolts, 2 nuts, No. 2 EGR pipe, No. 2 EGR pipe gasket and EGR inlet gasket from the EGR valve assembly and intake manifold.

  12. REMOVE INTAKE MANIFOLD


    1. A01FV2A

      Detach the clamp to disconnect the fuel tube from the wire harness clamp bracket.

    2. A01FSEI

      Disconnect the No. 2 fuel vapor feed hose from the intake manifold.

    3. Slide the clip and disconnect the ventilation hose from the intake manifold.

    4. Detach the clamp to disconnect the ventilation hose from the wire harness clamp bracket.

    5. Detach the 7 wire harness clamps to disconnect the wire harness from the 2 wire harness clamp brackets and intake manifold.

      A01FQ7Z

    6. Detach the clamp to disconnect the No. 2 water by-pass hose from the intake manifold.

    7. Remove the 3 bolts and 2 wire harness clamp brackets from the intake manifold.

    8. A01FQRM

      Remove the 7 bolts, intake manifold stay and intake manifold.

    9. Remove the gasket from the intake manifold.

  13. REMOVE EGR HOLE COVER PLATE (w/o EGR System)


    1. A01FSPJ

      Remove the 2 nuts, EGR hole cover plate and EGR inlet gasket from the intake manifold.

  14. REMOVE STUD BOLT

    Note

    If a stud bolt is deformed or its threads are damaged, replace it.


    1. A01FR2O

      Using an E6 "TORX" socket wrench, remove the 4 stud bolts from the intake manifold.