OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Sub-assembly RH)

         Disconnect the outer rear view mirror sub-assembly RH connector.

      2. Apply battery voltage and check the operation of the mirror.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (MR+) Battery negative (-) → Terminal 8 (MV) Turns upward Battery positive (+) → Terminal 8 (MV) Battery negative (-) → Terminal 3 (MR+) Turns downward Battery positive (+) → Terminal 7 (MH) Battery negative (-) → Terminal 3 (MR+) Turns left Battery positive (+) → Terminal 3 (MR+) Battery negative (-) → Terminal 7 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror sub-assembly RH.

   2. Check the operation of the retractable mirror (w/ Mirror Retract Switch).

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      
      
      1. 

         Text in Illustration

         *a	(A) Forward Position
         *b	(B)
         *c	(C) Driving position
         *d	(D)
         *e	(E) Retracted Position
         *f	Component without harness connected (Outer Rear View Mirror Sub-assembly RH)

         Disconnect the outer rear view mirror sub-assembly RH connector.

      2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         OK

         Tester Connection Condition Specified Condition Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) Forward position (A) Does not move Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) Driving position (C) Does not move Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 2 (MFR) Battery negative (-) → Terminal 6 (MRR) Retracted position (E) Does not move Battery positive (+) → Terminal 6 (MRR) Battery negative (-) → Terminal 2 (MFR) Retracted position (E) Moves from (E) to driving position (C)

         If the result is not as specified, replace the outer rear view mirror sub-assembly RH.

   3. Check the operation of the mirror heater (w/ Mirror Heater).

      
      

      1. Disconnect the outer rear view mirror sub-assembly RH connector.

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 4 (+) - 10 (-) 25°C (75°F) 9.6 to 14.4 Ω

         If the result is not as specified, replace the outer rear view mirror sub-assembly RH.

      2. Connect the cable from the positive (+) terminal to terminal 4 (+) and the negative battery (-) terminal to terminal 10 (-), then check that the mirror becomes warm.

         Tech Tips

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, replace the outer rear view mirror sub-assembly RH.

2. INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Sub-assembly LH)

         Disconnect the outer rear view mirror sub-assembly LH connector.

      2. Apply battery voltage and check the operation of the mirror.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (ML+) Battery negative (-) → Terminal 8 (MV) Turns upward Battery positive (+) → Terminal 8 (MV) Battery negative (-) → Terminal 3 (ML+) Turns downward Battery positive (+) → Terminal 7 (MH) Battery negative (-) → Terminal 3 (ML+) Turns left Battery positive (+) → Terminal 3 (ML+) Battery negative (-) → Terminal 7 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror sub-assembly LH.

   2. Check the operation of the retractable mirror (w/ Mirror Retract Switch).

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      
      
      1. 

         Text in Illustration

         *a	(A) Forward Position
         *b	(B)
         *c	(C) Driving position
         *d	(D)
         *e	(E) Retracted Position
         *f	Component without harness connected (Outer Rear View Mirror Sub-assembly LH)

         Disconnect the outer rear view mirror sub-assembly LH connector.

      2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         OK

         Tester Connection Condition Specified Condition Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) Forward position (A) Does not move Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) Driving position (C) Does not move Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 6 (MRL) Battery negative (-) → Terminal 2 (MFL) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 2 (MFL) Battery negative (-) → Terminal 6 (MRL) Retracted position (E) Does not move Battery positive (+) → Terminal 66 (MRL) Battery negative (-) → Terminal 2 (MFL) Retracted position (E) Moves from (E) to driving position (C)

         If the result is not as specified, replace the outer rear view mirror sub-assembly LH.

   3. Check the operation of the mirror heater (w/ Mirror Heater).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 4 (+) - 10 (-) 25°C (75°F) 9.6 to 14.4 Ω

         If the result is not as specified, replace the outer rear view mirror sub-assembly LH.

      2. Connect the cable from the positive (+) terminal to terminal 4 (+) and the negative battery (-) terminal to terminal 10 (-), then check that the mirror becomes warm.

         Tech Tips

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, replace the outer rear view mirror sub-assembly LH.