ROOF HEADLINING INSTALLATION

PROCEDURE

1. INSTALL ROOF HEADLINING ASSEMBLY

   
   

   1. 

      Put the roof headlining assembly into the vehicle through the front passenger side door.

      Note

      Do not damage the roof headlining assembly or body interior.

   2. Engage the clip at the front of the roof headlining, and install the roof headlining assembly.

   3. Connect the antenna cord sub-assembly connectors.

   4. Install the 3 clips at the rear of the roof headlining.

   5. Engage the 2 clamps and connect the connector from the front pillar LH.

   6. Engage the 3 clamps and connect the connector from the front pillar RH.

2. INSTALL VISOR HOLDER

   
   

   1. Engage the 2 claws install the 2 visor holders.

3. INSTALL VISOR ASSEMBLY LH

   
   

   1. Connect the connector (w/ Illumination).

   2. Install the visor assembly LH with the 2 screws.

4. INSTALL VISOR ASSEMBLY RH

   Tech Tips

   Use the same procedure as for the LH side.

5. INSTALL MAP LIGHT ASSEMBLY

   Click here

6. INSTALL CENTER PILLAR GARNISH LH

   
   

   1. Engage the 2 guides and clip.

   2. Install the center pillar garnish LH with the 2 bolts and clip.

      Torque:

      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

7. INSTALL CENTER PILLAR GARNISH RH

   Tech Tips

   Use the same procedure as for the LH side.

8. INSTALL REAR QUARTER TRIM GARNISH FRONT LH

   
   

   1. Engage the claw and clip.

   2. Install the rear quarter trim front garnish LH with the 2 bolts.

      Torque:

      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

9. INSTALL REAR QUARTER TRIM FRONT GARNISH RH

   Tech Tips

   Use the same procedure as for the LH side.

10. INSTALL REAR WINDOW SIDE GARNISH LH

    
    

    1. Engage the guide and 2 clips.

    2. Install the rear window side garnish LH with the bolt.

       Torque:

       7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

11. INSTALL REAR WINDOW SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

12. INSTALL QUARTER TRIM LID SUB-ASSEMBLY LH

    
    

    1. Install the 2 lid cover clips from the quarter trim lid sub-assembly LH.

       Note

       If there is any damage, be sure to replace the lid cover clip with a new one.

    2. 

       Text in Illustration

       *1	Lid Cover Clip

       Engage the 2 guides and 6 claws and install the quarter trim lid sub-assembly LH.

13. INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

14. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

    
    

    1. Engage the 8 clips install the quarter trim panel assembly LH.

    2. Install the clip.

15. INSTALL LUGGAGE COMPARTMENT TRIM COVER RH

    Tech Tips

    Use the same procedure as for the for LH side.

16. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH

    
    

    1. Fold down the rear seatback assembly.

    2. Engage the 2 clips install the luggage compartment inner trim cover LH.

17. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

18. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH

    Click here

19. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH

    Click here

20. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

21. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

22. INSTALL COWL SIDE TRIM BOARD LH

    
    

    1. Engage the 2 clips install the cowl side trim board LH.

    2. Install the clip.

23. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

24. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    
    
    1. 

       Text in Illustration

       *a	Alignment Mark

       Align the alignment mark on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

       Note

       After installation, check that the corners fit correctly.

25. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

26. INSTALL FRONT DOOR SCUFF PLATE LH

    
    

    1. Engage the 6 claws install the front door scuff plate LH.

27. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

28. INSTALL FRONT PILLAR GARNISH LH

    Click here

29. INSTALL FRONT PILLAR GARNISH RH

    Click here

30. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

31. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:

    6.0 N*m  { 61 kgf*cm, 53 in.*lbf }