PROCEDURE
INSPECT SPEEDOMETER
Check the operation.
Using a speedometer tester (calibrated chassis dynamometer), check the speedometer indication according to the table below.
except TFT Meter Type
| Chassis Dynamometer Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.1 to 24.5 |
| 40 | 41.8 to 45.6 |
| 60 | 62.4 to 66.8 |
| 80 | 83.3 to 87.7 |
| 100 | 104.2 to 108.6 |
| 120 | 125.1 to 129.5 |
| 140 | 146.0 to 150.4 |
| 160 | 166.9 to 171.3 |
| 180 | 187.8 to 192.2 |
| 200 | 208.7 to 213.1 |
| 220 | 229.6 to 234.0 |
| 240 | 250.5 to 254.9 |
| Chassis Dynamometer Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.1 to 24.5 |
| 40 | 41.4 to 45.2 |
| 60 | 61.6 to 66.0 |
| 80 | 82.1 to 86.5 |
| 100 | 102.6 to 107.0 |
| 120 | 123.1 to 127.5 |
| 140 | 143.6 to 148.0 |
| 160 | 164.1 to 168.5 |
| 180 | 184.6 to 189.0 |
| 200 | 205.1 to 209.5 |
| 220 | 225.6 to 230.0 |
| 240 | 246.1 to 250.5 |
| Chassis Dynamometer Indication (mph) | Acceptable Range (mph) |
|---|---|
| 20 | 20.8 to 23.2 |
| 40 | 41.6 to 44.2 |
| 60 | 62.5 to 65.1 |
| 80 | 83.4 to 86.0 |
| 100 | 104.3 to 106.9 |
| 120 | 125.2 to 127.8 |
| 140 | 146.1 to 148.7 |
for TFT Meter Type
| Chassis Dynamometer Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.1 to 24.5 |
| 40 | 41.3 to 45.1 |
| 60 | 61.4 to 65.8 |
| 80 | 81.8 to 86.2 |
| 100 | 102.2 to 106.6 |
| 120 | 122.6 to 127.0 |
| 140 | 143.0 to 147.4 |
| 160 | 163.4 to 167.8 |
| 180 | 183.8 to 188.2 |
| 200 | 204.2 to 208.6 |
| 220 | 224.6 to 229.0 |
| 240 | 245.0 to 249.4 |
| Chassis Dynamometer Indication (mph) | Acceptable Range (mph) |
|---|---|
| 10 | 10.5 to 12.7 |
| 20 | 20.6 to 23.0 |
| 40 | 40.9 to 43.5 |
| 60 | 61.3 to 63.9 |
| 80 | 81.7 to 84.3 |
| 100 | 102.1 to 104.7 |
| 120 | 117.5 to 125.1 |
| 140 | 137.1 to 145.5 |
Note
Tire wear, over inflation, or under inflation will cause errors.
Check the deviation from the acceptable range of the speedometer indication.
| Reference |
|---|
| Less than 0.5 km/h (0.3 mph) |
Tech Tips
If the indication is not as specified, go to the problem symptoms table Click here.
INSPECT TACHOMETER
Connect a tune-up tachometer, and start the engine.
Compare the test results with the tachometer indications.
| Tune-up Tachometer Indication (rpm) | Acceptable Range (rpm) |
|---|---|
| 1000 | 933 to 1067 |
| 2000 | 1923 to 2077 |
| 3000 | 2913 to 3088 |
| 4000 | 3913 to 4088 |
| 5000 | 4913 to 5088 |
| 6000 | 5913 to 6088 |
| 7000 | 6913 to 7088 |
| 8000 | 7913 to 8088 |
Tech Tips
If the indication is not as specified, go to the Problem Symptoms Table Click here.
INSPECT INDICATOR AND WARNING LIGHTS
Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.
| Warning or Indicator Light | Specified Condition |
|---|---|
| Low Fuel*1 | Warning or indicator light comes on for about 2 seconds after turning the ignition switch to ON. |
| Water Temperature Hot*2 | |
| Master Warning*2 | |
| A/T Oil Temperature*1*3 | Warning or indicator light comes on for about 2 or 3 seconds after turning the ignition switch to ON. |
| Headlight Leveling | Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON. |
| Brake | |
| TRC OFF | |
| VSC OFF | |
| Tire Pressure*4 | |
| TRACK | |
| SRS Airbag | Warning light comes on for about 6 seconds after turning the ignition switch to ON. |
| Charge | The light goes off right after the engine starts. |
| Oil pressure | |
| MIL (Check engine warning light) | |
| EPS | |
| Slip | The light goes off 3 minutes after starting the engine. |
| ABS |
*1: except TFT Meter Type
*2: for TFT Meter Type
*3: for Automatic Transmission System
*4: w/ Tire Pressure Warning System