LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door Courtesy SW Driver side door courtesy light switch signal/ON or OFF

      ON: Driver side door closed

      OFF: Driver side door open

      		 -
      D-Door Lock Pos SW Driver side door unlock detection switch signal/LOCK or UNLOCK

      LOCK: Driver side door locked

      UNLOCK: Driver side door unlocked

      		 -
      P Door Courtesy SW Passenger side door courtesy light switch signal/ON or OFF

      ON: Passenger side door closed

      OFF: Passenger side door open

      		 -
      P-Door Lock Pos SW Passenger side door unlock detection switch signal/LOCK or UNLOCK

      LOCK: Passenger side door locked

      UNLOCK: Passenger side door unlocked

      		 -
      Luggage Courtesy SW Luggage compartment door courtesy switch signal/ON or OFF

      ON: Luggage compartment door open

      OFF: Luggage compartment door closed

      		 -
      IG SW Ignition switch ON signal/ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 -
      ACC SW Ignition switch ACC signal/ON or OFF

      ON: Ignition switch ACC

      OFF: Ignition switch off

      		 -
      Room Light Output Map light assembly output signal/ON or OFF

      ON: Map light assembly on

      OFF: Map light assembly off

      		 -
      Key Illumination Output Ignition key cylinder light output signal/ON or OFF

      ON: Ignition key cylinder light on

      OFF: Ignition key cylinder light off

      		 -
      D Door Courtesy Light Driver courtesy light output signal/ON or OFF

      ON: Driver courtesy light on

      OFF: Driver courtesy light off

      		 -
      P Door Courtesy Light Passenger courtesy light output signal/ON or OFF

      ON: Passenger courtesy light on

      OFF: Passenger courtesy light off

      		 -
      Lighting Time Lighting time of the delay control function (illuminated entry system)/15s, 7.5s or 30s

      15s: 15 seconds

      7.5s: 7.5 seconds

      30s: 30 seconds

      		 Customized value is displayed
      I/L when ACC OFF Function that lights up the interior lights when the ignition switch is turned from on (ACC or IG) to off/OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed
      I/L ON W/Door Key Unlock Function that lights up the interior lights when the doors are unlocked/OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed
      Room Light when Aprchd Function that lights up the interior lights when a key enters any actuation area/OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed
      Interior Light Control Operation of the illuminated entry system/OFF or ON

      OFF: System not operated

      ON: System operated

      		 Customized value is displayed

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Illuminated Entry System

      • Map light assembly

      • Engine switch*1

      • Ignition key cylinder light*2

      		 ON/OFF Map light assembly switch in DOOR position
      Driver Courtesy Lamp Driver courtesy light ON/OFF -
      Passenger Courtesy Lamp Passenger courtesy light ON/OFF -
      Key Ring Light*2 Ignition key cylinder light ON/OFF -

      • *1: w/ Entry and Start System

      • *2: w/o Entry and Start System