VEHICLE STABILITY CONTROL SYSTEM TERMINALS OF ECU


  1. TERMINALS OF ECU

    A004HJAE01
    Text in Illustration
    *a

    Component without harness connected

    (Skid Control ECU (Brake Actuator Assembly))

    		 - -
    Terminal No. (Symbol) Terminal Description
    1 (+BM) ABS motor relay power supply
    2 (SPD) Speed signal output
    3 - (Not used)
    4 (FR-) Front wheel speed RH (-) signal input
    5 - (Not used)
    6 - (Not used)
    7 - (Not used)
    8 (FL-) Front wheel speed LH (-) signal input
    9 (CSW2) TRACK switch input
    10 - (Not used)
    11 - (Not used)
    12 (CSW1) VSC OFF switch input
    13 (GND2) Pump motor ground
    14 (CANL) CAN communication line L
    15 - (Not used)
    16 (FR+) Front wheel speed RH (+) signal input
    17 (RR+) Rear wheel speed RH (+) signal input
    18 (RL-) Rear wheel speed LH (-) signal input
    19 (FL+) Front wheel speed LH (+) signal input
    20 - (Not used)
    21 - (Not used)
    22 - (Not used)
    23 - (Not used)
    24 - (Not used)
    25 (+BS) ABS solenoid relay power supply
    26 (CANH) CAN communication line H
    27 - (Not used)
    28 (IG1) IG1 power source input
    29 (RR-) Rear wheel speed RH (-) signal input
    30 (STP) Stop light switch input
    31 (RL+) Rear wheel speed LH (+) signal input
    32 - (Not used)
    33 - (Not used)
    34 - (Not used)
    35 - (Not used)
    36 - (Not used)
    37 - (Not used)
    38 (GND1) Skid control ECU ground

  2. TERMINAL INSPECTION


    1. Disconnect the connector and measure the voltage and resistance on the wire harness side.

      A004IBYE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      		 - -

      Tech Tips

      The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) because the connector is watertight.

      Standard
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A5-1 (+BM) - Body ground W - Body ground ABS motor relay power supply Always 11 to 14 V
      A5-9 (CSW2) - Body ground P - Body ground TRACK switch input TRACK switch held ON → OFF (Not pressed) Below 1 Ω → 10 kΩ or higher
      A5-12 (CSW1) - Body ground O - Body ground VSC OFF switch input VSC OFF switch held ON → OFF (Not pressed) Below 1 Ω → 10 kΩ or higher
      A5-13 (GND2) - Body ground B - Body ground Pump motor ground Always Below 1 Ω
      A5-25 (+BS) - Body ground G - Body ground ABS solenoid relay power supply Always 11 to 14 V
      A5-28 (IG1) - Body ground G-R - Body ground IG1 power source input Ignition switch ON 11 to 14 V
      A5-30 (STP) - Body ground R - Body ground Stop light switch input Stop light switch ON → OFF (Brake pedal depressed → released) 11 to 14 V* → Below 1.5 V
      A5-38 (GND1) - Body ground B - Body ground Skid control ECU ground Always Below 1 Ω

      Tech Tips

      *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.