AUTOMATIC TRANSMISSION SYSTEM Shift Paddle Switch Circuit

DESCRIPTION

When the shift lever is in M, it is possible to change into any gear using the steering assembly transmission shift switch.

Additionally, when the vehicle is being driving with the shift lever in D, operating the steering assembly transmission shift switch changes to selection of gears with the shift lever in D, enabling shifting to any gear.

WIRING DIAGRAM

A004ICHE07

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Read the value displayed on the GTS.

      OK
      Tester Display Condition Standard
      Sport Shift Up SW

      Continuously shift to "+" (upshift): ON

      Release "+" (up-shift): OFF

      		 -
      Sport Shift Down SW

      Continuously shift to "-" (down-shift): ON

      Release "-" (down-shift): OFF

      		 -

    OK

    CHECK INTERMITTENT PROBLEMS Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION SHIFT SWITCH ASSEMBLY - TCM)


    1. Disconnect the TCM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A19-1(SFTD) - Body ground

      Pull continuously

      "+"

      (Up shift)

      		 Below 1 Ω
      Release "+" or "-" 10 kΩ or higher
      A19-2(SFTU) - Body ground

      Pull continuously

      "-"

      (Down shift)

      		 Below 1 Ω
      Release "+" or "-" 10 kΩ or higher

    3. Connect the TCM connector.


    NG

    CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND) Click here

    OK

  3. REPLACE TCM


    1. Replace the TCM Click here.


    NEXT

    PERFORM THE RESET MEMORY Click here

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)


    1. Disconnect the spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      D77-2 - Body ground Always Below 1 Ω

    3. Connect the spiral cable sub-assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - TCM)


    1. Disconnect the TCM connector.

    2. Disconnect the spiral cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A19-1(SFTD) - D77-8 Always Below 1 Ω
      A19-2(SFTU) - D77-1 Always Below 1 Ω
      A19-1(SFTD) or D77-8 - Body ground Always 10 kΩ or higher
      A19-2(SFTU) or D77-1 - Body ground Always 10 kΩ or higher

    4. Connect the TCM connector.

    5. Connect the spiral cable sub-assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK TRANSMISSION SHIFT SWITCH ASSEMBLY (TRANSMISSION SHIFT SWITCH ASSEMBLY - SPIRAL CABLE)


    1. Disconnect the spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      z4-1 - z4-4

      Pull continuously

      "+"

      (Up shift)

      		 Below 1 Ω
      Release "+" or "-" 10 kΩ or higher
      z4-3 - z4-4

      Pull continuously

      "-"

      (Down shift)

      		 Below 1 Ω
      Release "+" or "-" 10 kΩ or higher

    3. Connect the spiral cable sub-assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY


    1. Inspect the transmission shift switch assembly Click here.


    OK

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    NG

    REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY Click here