LUGGAGE COMPARTMENT DOOR OPENER SYSTEM TERMINALS OF ECU


  1. CHECK COWL SIDE JUNCTION BLOCK LH AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    A01FTAOE01
    Text in Illustration
    *1 Main Body ECU (Multiplex Network Body ECU) - -

    1. Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH Click here.

    2. Connect the cowl side junction block LH connectors.

    3. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A-11(GND1) - Body ground None - Body ground Ground Always Below 1 Ω
      A-29 (ACC) - Body ground None - Body ground ACC power supply Power switch on (ACC) 11 to 14 V
      Power switch off Below 1 V
      A-30 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
      A-31 (ALTB) - Body ground None - Body ground Battery power supply Always 11 to 14 V
      A-32 (IG) - Body ground None - Body ground IG power supply Power switch on (IG) 11 to 14 V
      Power switch off Below 1 V

      If the result is not as specified, there may be a malfunction on the wire harness side.

    4. Install the main body ECU (multiplex network body ECU) to the cowl side junction block LH Click here.

    5. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      N13-5 (TMSW) - Body ground G - Body ground Luggage door opening cancel switch signal Luggage door opening cancel switch on Below 1 V
      Power switch off, all doors closed and luggage door opening cancel switch off Pulse generation
      N13-8 (TSW) - Body ground Y - Body ground Luggage door opening switch signal Luggage door opening switch on Below 1 V
      Power switch off, all doors closed and luggage door opening switch off Pulse generation
      N12-23 (TKUL) - Body ground GR - Body ground Luggage compartment door lock cylinder signal Power switch off, luggage compartment door lock cylinder operated Below 1 V
      Power switch off, luggage compartment door lock cylinder not operated Pulse generation
      N12-19 (LGCY) - Body ground* P - Body ground Luggage compartment door courtesy light switch assembly input signal Luggage compartment door open Below 1 V
      Luggage compartment door close 11 to 14 V
      5C-17 (TR+) - Body ground* Y - Body ground Luggage compartment door lock relay output signal Luggage door opening switch on Below 1 V
      Luggage door opening switch off 11 to 14 V

      • *: w/o Power Trunk Lid System

  2. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    A01FTANE33

    1. Disconnect the N94 and N95 certification ECU (smart key ECU assembly) connectors.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      N94-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
      N95-4 (CUTB) - Body ground P - Body ground Dark current cut fuse pin input signal* Always 11 to 14 V
      N95-5 (+B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
      N95-16 (IG) - Body ground B - Body ground Ignition power supply Power switch off Below 1 V
      Power switch on (IG) 11 to 14 V

      • *: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).

    3. Reconnect the N94 and N95 certification ECU (smart key ECU assembly) connectors.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      N98-22 (TSW5) - N94-1 (E) SB - W-B Luggage electrical key switch input signal Power switch on (IG), luggage compartment door is fully closed and luggage electrical key switch off Pulse generation

  3. CHECK LUGGAGE CLOSER MOTOR ASSEMBLY (w/ Power Trunk Lid System) Click here