POWER WINDOW REGULATOR MOTOR (for Front Door) INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. Apply MP grease to the sliding and rotating areas of the power window regulator motor assembly LH.

    2. Using a T25 "TORX" socket wrench, install the power window regulator motor assembly LH with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    2. Temporarily install the temporary bolt to the front door window regulator.

    3. A01FSARE01
      Text in Illustration
      *1 Temporary Bolt

      Install the front door window regulator with the 5 bolts, and then tighten the temporary bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Note

      Be careful not to drop the front door window regulator as it may become damaged.

    4. Connect the connector.

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Operate the front door window regulator so that the front door glass can be installed.

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Remove the power window regulator master switch assembly with front door armrest base panel.

    6. A01FV93E01

      Insert the front door glass into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

    7. Install the front door glass with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  4. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the front door panel.

    2. A01FV78E01
      Text in Illustration
      *a Reference Point

      Pass the front door inside locking cable and front door lock remote control cable through a new front door service hole cover, and then attach the front door service hole cover using the reference points on the front door panel.

      Tech Tips


      • Securely install the front door service hole cover to prevent wrinkles and air bubbles.

      • There should be no wrinkles or folds after installing the front door service hole cover.

      • After installing the front door service hole cover, check the seal quality.

  5. INSTALL FRONT DOOR ARMREST SET BRACKET LH


    1. Install the front door armrest set bracket with the 2 screws.

  6. INSTALL DOOR FRAME GARNISH LH


    1. Attach the 2 clips to install the door frame garnish.

  7. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. Install the front door inner glass weatherstrip.

  8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. Connect the front door lock remote control cable and front door inside locking cable.

    2. Connect each connector.

    3. A01FVSRE01
      Text in Illustration
      *1 Reference Boss

      Attach the 4 claws to install the front door trim board to the front door inner glass weatherstrip.

    4. Attach the reference boss in the direction indicated by the arrow in the illustration.

    5. Attach the 9 clips to install the front door trim board.

    6. Install the 3 screws.

  9. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. Attach the claw to install the courtesy light assembly.

  10. INSTALL FRONT DOOR HOLE COVER


    1. Install the front door hole cover.

  11. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT UPPER ARMREST BASE PANEL LH (for Driver Side)


    1. Connect the connector.

    2. Attach the 5 claws and 2 clips to install the power window regulator master switch assembly with front door armrest base panel.

  12. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT UPPER ARMREST BASE PANEL RH (for Front Passenger Side)


    1. Connect the connector.

    2. Attach the 2 clips, 3 guides and 5 claws to install the power window regulator switch assembly with front upper armrest base panel RH.

  13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. Install the front door hole cover.

  14. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH


    1. Install the luggage compartment trim cover LH.

  16. REMOVE LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.

  17. INITIALIZE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Click here

  18. CHECK POWER WINDOW

    Click here