POWER WINDOW CONTROL SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (desired system) / Data List.

    5. According to the display on the GTS, read the Data List.

      Master Switch
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver side power window auto up/down signal / ON or OFF

      ON: Front power window switch LH*1, RH*2 auto up/down on multiplex network master switch assembly operated

      OFF: Front power window switch LH*1, RH*2 on multiplex network master switch assembly not operated

      		 -
      P Door P/W Auto SW Front passenger side power window remote auto up/down signal / ON or OFF

      ON: Front power window switch RH*, LH*2 remote auto up/down on multiplex network master switch assembly operated

      OFF: Front power window switch RH*, LH*2 on multiplex network master switch assembly not operated

      		 -
      RR Door P/W Auto SW Rear power window RH remote auto up/down signal / ON or OFF

      ON: Rear power window switch RH remote auto up/down on multiplex network master switch assembly operated

      OFF: Rear power window switch RH on multiplex network master switch assembly not operated

      		 -
      RL Door P/W Auto SW Rear power window LH remote auto up/down signal / ON or OFF

      ON: Rear power window switch LH remote auto up/down on multiplex network master switch assembly operated

      OFF: Rear power window switch LH on multiplex network master switch assembly not operated

      		 -
      P Door P/W Up SW Front passenger side power window remote manual up signal / ON or OFF

      ON: Front power window switch RH remote manual up on multiplex network master switch assembly operated

      OFF: Front power window switch RH on multiplex network master switch assembly not operated

      		 -
      RR Door P/W up switch Rear power window RH remote manual up signal / ON or OFF

      ON: Rear power window switch RH remote manual up on multiplex network master switch assembly operated

      OFF: Rear power window switch RH on multiplex network master switch assembly not operated

      		 -
      RL Door P/W up switch Rear power window LH remote manual up signal / ON or OFF

      ON: Rear power window switch LH remote manual up on multiplex network master switch assembly operated

      OFF: Rear power window switch LH on multiplex network master switch assembly not operated

      		 -
      P Door P/W Down SW Front passenger side power window remote manual down signal / ON or OFF

      ON: Front power window switch RH*, LH*2 remote manual down on multiplex network master switch assembly operated

      OFF: Front power window RH*, LH*2 switch on multiplex network master switch assembly not operated

      		 -
      RR Door P/W Down SW Rear power window RH remote manual down signal / ON or OFF

      ON: Rear power window switch RH remote manual down on multiplex network master switch assembly operated

      OFF: Rear power window switch RH on multiplex network master switch assembly not operated

      		 -
      RL Door P/W Down SW Rear power window LH remote manual down signal / ON or OFF

      ON: Rear power window switch LH remote manual down on multiplex network master switch assembly operated

      OFF: Rear power window switch LH on multiplex network master switch assembly not operated

      		 -
      Window Lock Switch Status Power window lock switch / ON or OFF

      ON: Power window lock switch on

      OFF: Power window lock switch off

      		 -
      Number of Trouble Codes Number of trouble codes / Min.: 0, Max.: 255 Number of DTCs stored -

      • *1: for LHD

      • *2: for RHD

      D-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver side power window auto up/down signal / ON or OFF

      ON: Front power window switch LH*1, RH*2 auto up/down operated

      OFF: Front power window switch LH*1, RH*2 not operated

      		 -
      D Door P/W Up SW Driver side power window manual up signal / ON or OFF

      ON: Front power window switch LH*1, RH*2 manual up operated

      OFF: Front power window switch LH*1, RH*2 not operated

      		 -
      D Door P/W Down SW Driver side power window manual down signal / ON or OFF

      ON: Front power window switch LH*1, RH*2 manual down operated

      OFF: Front power window switch LH*1, RH*2 not operated

      		 -
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Motor operates normally between fully closed and 1/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution

      OK: Motor operates normally between 1/4 open and 1/2 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution

      OK: Motor operates normally between 1/2 open and 3/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution

      OK: Motor operates normally between 3/4 open and fully open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Number of Trouble Codes Number of trouble codes / Min.: 0, Max.: 255 Number of DTCs stored -

      • *1: for LHD

      • *2: for RHD

      P-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Auto SW Front passenger side power window auto up/down signal / ON or OFF

      ON: Front power window switch RH*1, LH*2 auto up/down operated

      OFF: Front power window switch RH*1, LH*2 not operated

      		 -
      P Door P/W Up SW Front passenger side power window manual up signal / ON or OFF

      ON: Front power window switch RH*1, LH*2 manual up operated

      OFF: Front power window switch RH*1, LH*2 not operated

      		 -
      P Door P/W Down SW Front passenger side power window manual down signal / ON or OFF

      ON: Front power window switch RH*1, LH*2 manual down operated

      OFF: Front power window switch RH*1, LH*2 not operated

      		 -
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Motor operates normally between fully closed and 1/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution

      OK: Motor operates normally between 1/4 open and 1/2 open positions

      Caution: Jam protection function operates due to detection of foreign object or irregular movement

      		 -
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution

      OK: Motor operates normally between 1/2 open and 3/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution

      OK: Motor operates normally between 3/4 open and fully open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Number of Trouble Codes Number of trouble codes / Min.: 0, Max.: 255 Number of DTCs stored -

      • *1: for LHD

      • *2: for RHD

      RL-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RL Door P/W Auto SW Rear power window LH auto up/down signal / ON or OFF

      ON: Rear power window switch LH auto up/down operated

      OFF: Rear power window switch LH not operated

      		 -
      RL Door P/W Up SW Rear power window LH manual up signal / ON or OFF

      ON: Rear power window switch LH manual up operated

      OFF: Rear power window switch LH not operated

      		 -
      RL Door P/W Down SW Rear power window LH manual down signal / ON or OFF

      ON: Rear power window switch LH manual down operated

      OFF: Rear power window switch LH not operated

      		 -
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Motor operates normally between fully closed and 1/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution

      OK: Motor operates normally between 1/4 open and 1/2 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution

      OK: Motor operates normally between 1/2 open and 3/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution

      OK: Motor operates normally between 3/4 open and fully open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Number of Trouble Codes Number of trouble codes / Min.: 0, Max.: 255 Number of DTCs stored -
      RR-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door P/W Auto SW Rear power window RH auto up/down signal / ON or OFF

      ON: Rear power window switch RH auto up/down operated

      OFF: Rear power window switch RH not operated

      		 -
      RR Door P/W Up SW Rear power window RH manual up signal / ON or OFF

      ON: Rear power window switch RH manual up operated

      OFF: Rear power window switch RH not operated

      		 -
      RR Door P/W Down SW Rear power window RH manual down signal / ON or OFF

      ON: Rear power window switch RH manual down operated

      OFF: Rear power window switch RH not operated

      		 -
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Motor operates normally between fully closed and 1/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution

      OK: Motor operates normally between 1/4 open and 1/2 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution

      OK: Motor operates normally between 1/2 open and 3/4 open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution

      OK: Motor operates normally between 3/4 open and fully open positions

      Caution: Jam protection function operating due to detection of foreign object or irregular movement

      		 -
      Number of Trouble Codes Number of trouble codes / Min.: 0, Max.: 255 Number of DTCs stored -
      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FR Door Courtesy Front door courtesy light switch RH signal / ON or OFF

      ON: Front door RH closed

      OFF: Front door RH open

      		 -
      FL Door Courtesy Front door courtesy light switch LH signal / ON or OFF

      ON: Front door LH closed

      OFF: Front door LH open

      		 -
      Front Left Door (for LHD)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Door Key Linked Lock SW Front door lock/unlock switch LH lock signal (key-linked lock switch) / ON or OFF

      ON: Front door LH key cylinder turned to lock position

      OFF: Front door LH key cylinder turned to unlock position

      		 -
      Door Key Linked Unlock SW Front door lock/unlock switch LH unlock signal (key-linked unlock switch) / ON or OFF

      ON: Front door LH key cylinder turned to unlock position

      OFF: Front door LH key cylinder turned to lock position

      		 -
      Front Right Door (for RHD)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Door Key Linked Lock SW Front door lock/unlock switch RH lock signal (key-linked lock switch) / ON or OFF

      ON: Front door RH key cylinder turned to lock position

      OFF: Front door RH key cylinder turned to unlock position

      		 -
      Door Key Linked Unlock SW Front door lock/unlock switch RH unlock signal (key-linked unlock switch) / ON or OFF

      ON: Front door RH key cylinder turned to unlock position

      OFF: Front door RH key cylinder turned to lock position

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (desired system) / Active Test.

    5. According to the display on the GTS, perform the Active Test.

      CAUTION:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

      D-Door Motor
      Tester Display Test Part Control Range Diagnostic Note
      Power Window Driver side power window OFF/UP/DOWN -
      P-Door Motor
      Tester Display Test Part Control Range Diagnostic Note
      Power Window Passenger side power window OFF/UP/DOWN -
      RL-Door Motor
      Tester Display Test Part Control Range Diagnostic Note
      Power Window Rear LH side power window OFF/UP/DOWN -
      RR-Door Motor
      Tester Display Test Part Control Range Diagnostic Note
      Power Window Rear RH side power window OFF/UP/DOWN -