REAR SUNSHADE ASSEMBLY REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE LUGGAGE COMPARTMENT FLOOR MAT (w/ Rear Seat Side Airbag)


    1. Remove the luggage compartment floor mat.

  2. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH (w/ Rear Seat Side Airbag)


    1. Remove the luggage compartment trim cover LH.

  3. PRECAUTION (w/ Rear Seat Side Airbag)

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

  4. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL (w/ Rear Seat Side Airbag)

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE REAR SEAT ASSEMBLY

    Click here

  6. REMOVE REAR DOOR SCUFF PLATE LH


    1. Place your hands on the inner portion of the rear door scuff plate LH and detach the 2 claws labeled A, 6 claws labeled B and 2 claws labeled C in the order shown in the illustration.

    2. Raise the rear door scuff plate LH to detach the 4 clips on the outer side and remove it.

      A01FQGSE01
      Text in Illustration
      *1 Claw A *2 Claw B
      *3 Claw C - -

  7. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE REAR SEAT SIDE GARNISH LH

    A01FQIB

    1. Detach the 4 claws and guide and remove the rear seat side garnish LH.

  9. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE INNER ROOF SIDE GARNISH LH

    A01FQFNE01

    1. w/ Rear Sunshade:


      1. Detach the 4 clips.

      2. Detach the 3 guides and the end of the rear window shade assembly, and then remove the inner roof side garnish LH.

        Text in Illustration
        *1 End Of The Rear Window Shade Assembly
        *2 Guide
    2. A01FRHI

      w/o Rear Sunshade:


      1. Detach the 4 clips and 3 guides and remove the inner roof side garnish LH.

  11. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. A01FTM2

      Using a moulding remover, detach the 4 claws and remove the 2 rear seat shoulder belt hole covers.

    2. A01FR9L

      Using a moulding remover, detach the 4 claws and remove the belt guide of the rear seat inner with center belt assembly LH.

    3. A01FRSY

      Using a moulding remover, detach the 4 claws and remove the 3 child restraint tether anchor covers.

    4. w/o Rear Sunshade:


      1. A01FQT4

        Detach the 4 claws, disconnect the connector and remove the center stop light cover.

      2. A01FRYW

        Detach the 4 clips, and then slide the package tray trim panel assembly towards the front of the vehicle to detach the 5 guides.

      3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly and remove the package tray trim panel assembly.

    5. w/ Rear Sunshade:


      1. A01FQH5

        Detach the 4 clips, and then slide the package tray trim panel assembly towards the front of the vehicle to detach it from the rear window shade assembly.

      2. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly and remove the package tray trim panel assembly.

  13. REMOVE CENTER STOP LIGHT COVER


    1. A01FQT4

      Detach the 4 claws and remove the center stop light cover.

    2. Disconnect the connector.

  14. REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY

    A01FS15

    1. Detach the 3 clips and 5 guides and remove the No. 2 package tray trim panel assembly.

  15. REMOVE REAR WINDOW SHADE ASSEMBLY

    A01FS9B

    1. Remove the 4 bolts.

    2. Disconnect the connector and remove the rear window shade assembly.