ENGINE HOOD COURTESY SWITCH INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL HOOD LOCK ASSEMBLY


    1. A01FT6S

      Apply MP grease to the sliding areas of the lock.

    2. Connect the hood lock control cable assembly.

    3. A01FVXP

      Move the hood lock in the direction of the arrows in the illustration to temporarily install it.

    4. Install the hood lock assembly with the 3 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  2. INSTALL HOOD LOCK CONTROL CABLE COVER


    1. Install the hood lock control cable cover with the 2 clips.

    2. Attach the 2 clamps and connect the connector.

  3. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    Click here

  4. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    A01FRHXE02
    Text in Illustration
    *1 Approx. 10 m (32.8 ft.)
    *2 Approx. 14 m (45.9 ft.)

    Note


    • Perform measurements on a level surface.

    • Make sure that no large pieces of metal are within a 10 m (32.8 ft.) x 14 m (45.9 ft.) area in front of the vehicle. If possible, the surrounding area should also be free of large metal objects.


    1. Before adjusting the radar beam axis, prepare the vehicle as follows.


      1. Remove all excess weight from the vehicle (luggage, heavy objects, etc.).

      2. Check the tire pressure and adjust it if necessary Click here.

    2. A01FVQYE01
      Text in Illustration
      *1 Level

      Check and adjust the vertical direction of the radar sensor.


      1. Remove dust, oil and foreign matter from the radar sensor's level rack.

      2. Set a level on the radar sensor's level rack.

      3. A01FVRVE01
        Text in Illustration
        *1 Level
        *2 Air Bubble
        *3 Bolt A
        *a FR
        *b LH

        Check that the level's air bubble is within the red frame.

        OK
        Level's air bubble is within the red frame.

        If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the air bubble is within the red frame.

        Tech Tips


        • The adjustable range within the level's red frame is +/- 0.2°.

        • The target angle is +0.2° (upward angle of 0.2°).

          Adjustment
          Adjustment Direction Adjustment Procedure Adjustment Angle
          Vertical adjustment Upward direction: Turn bolt A to negative (-) side For 1 complete turn of screwdriver, sensor moves about 0.12°
          Downward direction: Turn bolt A to positive (+) side
    3. A01FPY7E01
      Text in Illustration
      *1 Millimeter Wave Radar Sensor

      Adjust the reflector height.


      1. Adjust the reflector so that the center of SST reflector is the same height as the millimeter wave radar sensor.

        SST
        09870-60000   ( 09870-60010 )
        09870-60040

        Tech Tips

        Prepare a 10 m (32.8 ft.) string, a string with a sharp-pointed weight (plumb bob), and a 5 m (16.4 ft.) tape measure.

    4. A01FSD0E01

      Place the reflector.


      1. Hang the string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle.

      2. A01FTAXE02
        Text in Illustration
        *a Adjust Center By Moving String To Right And Left
        *b Extend String Through Front Center Mark

        Set one end of the 10 m (32.8 ft.) string on the vehicle's rear center point. Run the string over the vehicle's front center point to a position 5 m (16.4 ft.) beyond the vehicle's front center point as shown in the illustration. Mark the 5 m (16.4 ft.) position.

      3. Place the reflector (SST) at the marked position.

        Note

        Perform the operation as precisely as possible.

        A01FTUVE03
        Text in Illustration
        *a Reflector (SST) Placement Point *b Millimeter Wave Radar Sensor Position
        *c 5 m (16.4 ft.) *d 13.1 mm (0.516 in.)

    5. Check the radar beam axis.


      1. When using the GTS:


        1. Connect the GTS to the DLC3.

        2. Turn the power switch on (IG).

        3. Turn the GTS on, and turn the cruise control main switch on.

        4. Select "Connect to Vehicle".

        5. Select each item on the display screen and proceed to the next screen.

        6. Under "System Selection Menu", select "Radar Cruise".

        7. Select "Utility".

        8. Select "Beam Axis Adjustment" and proceed to the next screen.

          Tech Tips

          A buzzer will sound for 1 second.

        9. Follow the GTS display, and continue with the adjustment.

          Note


          • Turn the cruise control main switch on before pressing "Next".

          • Make sure there is at least 20 cm (7.87 in.) between the radar sensor and any nearby individuals.

      2. Check the following items on the radar cruise divergence data screen.

        Note

        While using the GTS beam axis adjustment mode, the actual direction and angle of the radar sensor may be different from the GTS data. In such a case, the deviation is displayed on the multi-information display in the combination meter.


        1. Confirm that the distance value is approximately 5 m (16.4 ft.).

          Tech Tips


          • A value between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.) should be indicated.

          • If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the Notice at the beginning of this adjustment procedure).

        2. Confirm that the left/right side value is between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.).

          Tech Tips

          If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the Notice at the beginning of this adjustment procedure).

    6. Check and adjust the horizontal direction of the radar sensor.


      1. Check that the divergence of the radar beam axis is 0°.

        Standard
        0° (Both right and left)

        If the axis is not as specified, use a screwdriver to adjust bolt B until the divergence of the radar beam axis is 0°.

      2. A01FVHGE01
        Text in Illustration
        *1 Bolt B

        Based on the measured divergence of the beam axis, turn and adjust bolt B for horizontal adjustment of the millimeter wave radar sensor using a screwdriver.

        Adjustment
        Adjustment Direction Adjustment Procedure Adjustment Angle
        Horizontal adjustment Right direction: Turn bolt B to positive (+) side. For 1 complete turn of screwdriver, sensor moves about 0.07°
        Left direction: Turn bolt B to negative (-) side.

        Tech Tips

        If the value does not change to 0°, it is possible that the sensor is aiming at something different. Reconfirm that there are no reflective materials in the surrounding area.

      3. Finish the beam axis adjustment.

      4. Disconnect the GTS from the DLC3.

    7. Recheck and readjust the vertical direction of the radar sensor.


      1. A01FVQYE01
        Text in Illustration
        *1 Level

        Set a level on the radar sensor's level rack.

      2. A01FVRVE01
        Text in Illustration
        *1 Level
        *2 Air Bubble
        *3 Bolt A
        *a FR
        *b LH

        Check that the level's air bubble is within the red frame.

        OK
        Level's air bubble is within the red frame.

        If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the level's air bubble is within the red frame.

        Tech Tips


        • The adjustable range within the red frame is +/- 0.2°.

        • The target angle is + 0.2° (upward angle of 0.2°).

          Adjustment
          Adjustment Direction Adjustment Procedure Adjustment Angle
          Vertical adjustment Upward direction: Turn bolt A to negative (-) side For 1 complete turn of screwdriver, sensor moves about 0.12°
          Downward direction: Turn bolt A to positive (+) side

  5. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 7 clips.

  6. INSTALL ENGINE ROOM COVER SIDE


    1. Install the engine room side cover with the 4 clips.