LIGHTING SYSTEM ACC Signal Circuit

DESCRIPTION

This circuit detects whether the power switch is on (ACC) or off, and sends this information to the main body ECU.

WIRING DIAGRAM

A01FTEOE02

INSPECTION PROCEDURE

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

PROCEDURE


  1. READ VALUE USING GTS (ACC SW)


    1. Using the GTS, read the Data List Click here.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Power switch on (ACC) signal / ON or OFF

      ON: Power switch on (ACC)

      OFF: Power switch off

      		 "ON" is also displayed for this item when the power switch is on (IG).
      OK
      The display is as specified in the normal condition column.

    NG

    CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - BATTERY AND BODY GROUND) Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - BATTERY AND BODY GROUND)


    1. A01FSZYE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Cowl Side Junction Block RH)

      Disconnect the cowl side junction block RH connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      4E-1 - Body ground Always 11 to 14 V
      4A-19 - Body ground Power switch on (ACC) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4A-4 - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT COWL SIDE JUNCTION BLOCK RH (RH ACC RELAY)


    1. A01FTD7E02

      Remove the cowl side junction block RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4E-1 - 4A-45 Battery voltage not applied between terminals 4A-19 and 4A-4 10 kΩ or higher
      Battery voltage applied between terminals 4A-19 and 4A-4 Below 1 Ω

    NG

    REPLACE COWL SIDE JUNCTION BLOCK RH

    OK

  4. CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - COWL SIDE JUNCTION BLOCK LH)


    1. Disconnect the 4A cowl side junction block RH connector.

    2. Disconnect the 5B cowl side junction block LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4A-45 - 5B-19 Always Below 1 Ω
      4A-45 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT COWL SIDE JUNCTION BLOCK LH


    1. A01FQY9E01

      Remove the cowl side junction block LH Click here.

    2. Remove the main body ECU from the cowl side junction block LH Click here.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5B-19 - A-29 (ACC) Always Below 1 Ω

    NG

    REPLACE COWL SIDE JUNCTION BLOCK LH Click here

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here