WIRELESS DOOR LOCK CONTROL SYSTEM TERMINALS OF ECU


  1. CHECK COWL SIDE JUNCTION BLOCK LH AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    A01FTAOE01
    Text in Illustration
    *1 Main Body ECU (Multiplex Network Body ECU) - -

    1. Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH Click here.

    2. Connect the cowl side junction block LH connectors.

    3. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω
      A-29 (ACC) - Body ground None - Body ground ACC power supply Power switch on (ACC) 11 to 14 V
      Power switch off Below 1 V
      A-30 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
      A-31 (ALTB) - Body ground None - Body ground Battery power supply Always 11 to 14 V
      A-32 (IG) - Body ground None - Body ground IG power supply Power switch on (IG) 11 to 14 V
      Power switch off Below 1 V

    4. Install the main body ECU (multiplex network body ECU) to the cowl side junction block LH Click here.

    5. Measure the voltage according to the value(s) in the table below.

      for LHD
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      5A-11 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output signal (front passenger side door and rear door RH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder unlocked 11 to 14 V
      5A-13 (ACT+) - Body ground G - Body ground Door lock motor lock drive output signal (front passenger side door and rear door RH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      5A-33 (FRCY) - Body ground R - Body ground Front door courtesy light switch assembly RH input signal Front door RH open Below 1 V
      Front door RH closed Pulse generation
      5C-8 (ACT+) - Body ground G - Body ground Door lock motor lock drive output signal (rear door LH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      5C-9 (ACT+) - Body ground G - Body ground Door lock motor lock drive output signal (driver door) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      5C-10 (ACTD) - Body ground L - Body ground Door lock motor unlock drive output signal (driver door) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder unlocked 11 to 14 V
      5C-12 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output signal (rear door LH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder unlocked 11 to 14 V
      5C-30 (LSWL) - Body ground B - Body ground Rear door LH unlock detection switch input signal Rear door LH unlocked Below 1 V
      Power switch off, all doors closed and rear door LH locked Pulse generation
      5C-44 (FLCY) - Body ground R - Body ground Front door courtesy light switch assembly LH input signal Front door LH open Below 1 V
      Front door LH closed Pulse generation
      5D-27 (BZR) - Body ground G - Body ground Wireless door lock buzzer output signal Power switch off, all doors closed and electrical key transmitter sub-assembly off → on (answer-back) Below 1V → Pulse generation
      N11-3 (LCTY) - Body ground G - Body ground Rear door courtesy light switch assembly LH input signal Rear door LH open Below 1 V
      Rear door LH closed Pulse generation
      N12-6 (RCTY) - Body ground G - Body ground Rear door courtesy light switch assembly RH input signal Rear door RH open Below 1 V
      Rear door RH closed Pulse generation
      N12-7 (LSFL) - Body ground SB - Body ground Front door LH unlock detection switch input signal Front door LH unlocked Below 1 V
      Power switch off, all doors closed and front door LH locked Pulse generation
      N12-18 (LSFR) - Body ground SB - Body ground Front door RH unlock detection switch input signal Front door RH unlocked Below 1 V
      Power switch off, all doors closed and front door RH locked Pulse generation
      N13-2 (LSWR) - Body ground B - Body ground Rear door RH unlock detection switch input signal Rear door RH unlocked Below 1 V
      Power switch off, all doors closed and rear door RH locked 11 to 14 V
      for RHD
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      5A-1 (ACTD) - Body ground L - Body ground Door lock motor unlock drive output signal (driver side) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder unlocked 11 to 14 V
      5A-11 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output signal (rear door RH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder unlocked 11 to 14 V
      5A-13 (ACT+) - Body ground G - Body ground Door lock motor lock drive output signal (driver door and rear door RH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      5A-33 (FRCY) - Body ground R - Body ground Front door courtesy light switch assembly RH input signal Front door RH open Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      Front door RH closed Pulse generation
      5C-8 (ACT+) - Body ground G - Body ground Door lock motor lock drive output signal (rear door LH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      5C-3 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output signal (front passenger door) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder unlocked 11 to 14 V
      5C-8 (ACT+) - Body ground G - Body ground Door lock motor lock drive output signal (rear door LH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      5C-9 (ACT+) - Body ground G - Body ground Door lock motor lock drive output signal (front passenger door) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder locked 11 to 14 V
      5C-12 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output signal (rear door LH) Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder off Below 1 V
      Multiplex network master switch assembly (door control switch), power window regulator switch assembly (door control switch) or driver door key cylinder unlocked 11 to 14 V
      5C-30 (LSWL) - Body ground GR - Body ground Rear door LH unlock detection switch input signal Rear door LH unlocked Below 1 V
      Power switch off, all doors closed and rear door LH locked Pulse generation
      5C-44 (FLCY) - Body ground R - Body ground Front door courtesy light switch assembly LH input signal Front door LH open Below 1 V
      Front door LH closed Pulse generation
      5A-60 (GSW) - Body ground B - Body ground Wireless door lock buzzer output signal Power switch off, all doors closed and electrical key transmitter sub-assembly off → on (answer-back) Below 1V → Pulse generation
      N11-3 (LCTY) - Body ground G - Body ground Rear door courtesy light switch assembly LH input signal Rear door LH open Below 1 V
      Rear door LH closed Pulse generation
      N12-6 (RCTY) - Body ground G - Body ground Rear door courtesy light switch assembly RH input signal Rear door RH open Below 1 V
      Rear door RH closed Pulse generation
      N12-7 (LSFL) - Body ground SB - Body ground Front door LH unlock detection switch input signal Front door LH unlocked Below 1 V
      Power switch off, all doors closed and front door LH locked Pulse generation
      N12-18 (LSFR) - Body ground SB - Body ground Front door RH unlock detection switch input signal Front door RH unlocked Below 1 V
      Power switch off, all doors closed and front door RH locked Pulse generation
      N13-2 (LSWR) - Body ground P - Body ground Rear door RH unlock detection switch input signal Rear door RH unlocked Below 1 V
      Power switch off, all doors closed and rear door RH locked 11 to 14 V

  2. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    A01FTANE33

    1. Disconnect the N94 and N95 certification ECU (smart key ECU assembly) connectors.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      N94-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
      N95-4 (CUTB) - Body ground P - Body ground Dark current cut fuse pin input signal* Always 11 to 14 V
      N94-5 (+B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
      N95-16 (IG) - Body ground B - Body ground IG power supply Power switch off Below 1 V
      Power switch on (IG) 11 to 14 V

      • *: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).

    3. Reconnect the N94 and N95 certification ECU (smart key ECU assembly) connectors.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      N98-7 (CSEL) - N94-1 (E) P - W-B Communication channel switching circuit

        Procedure:

      1. Power switch off

      2. All doors closed

      		 Below 1 V → 4.5 to 6 V → Below 1 V
      N98-6 (RDAM) - N94-1 (E) R - W-B Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly).

        Procedure:

      1. Power switch off

      2. All doors locked

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      		 Pulse generation (See waveform 2)
      N98-15 (RCO) - N94-1 (E)

      G - W-B*3

      LG - W-B*4

      		 Output to door control receiver (Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)

        Procedure:

      1. Power switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      		 Pulse generation (See waveform 1)
      N98-16 (ASEL) - N94-1 (E) L - W-B Communication antenna switching circuit

        Procedure:

      1. Power switch off

      2. All doors closed

      		 Below 1 V → 4.5 to 6 V → Below 1 V

      • *1: For details about the areas that are outside the entry function detection area, refer to Operation Check Click here.

      • *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check Click here.

      • *3: for LHD

      • *4: for RHD

    5. A01FQSNE01
      Text in Illustration
      *a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
      *b After lock or unlock switch of electrical key transmitter sub-assembly pressed

      Using an oscilloscope, check waveform 1.

      Tech Tips

      The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

      Waveform 1 (Reference)
      Item Content
      Tester Connection N98-15 (RCO) - N94-1 (E)
      Tool Setting 2 V/DIV., 500 ms/DIV.
      Condition

        Procedure:

      1. Power switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      • *1: For details about the areas that are outside the entry function detection area, refer to Operation Check Click here.

      • *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check Click here.

    6. A01FTKKE01
      Text in Illustration
      *a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
      *b After lock or unlock switch of electrical key transmitter sub-assembly pressed

      Using an oscilloscope, check waveform 2.

      Tech Tips

      The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

      Waveform 2 (Reference)
      Item Content
      Tester Connection N98-6 (RDAM) - N94-1 (E)
      Tool Setting 5 V/DIV., 500 ms/DIV.
      Condition

        Procedure:

      1. Power switch off

      2. All doors locked

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      • *1: For details about the areas that are outside the entry function detection area, refer to Operation Check Click here.

      • *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check Click here.

  3. CHECK DOOR CONTROL RECEIVER (for 12 Pin Type)

    A01FUXEE01

    1. Disconnect the T32 door control receiver connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T32-1 (IG) - Body ground LG - Body ground IG power supply Power switch off Below 1 V
      Power switch on (IG) 11 to 14 V
      T32-7 (+B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
      T32-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Reconnect the T32 door control receiver connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T32-6 (CSEL) - T32-12 (GND) P - W-B Communication channel switching circuit

        Procedure:

      1. Power switch off

      2. All doors closed

      		 Below 1 V → 4.5 to 6 V → Below 1 V
      T32-9 (DATA) - T32-12 (GND) R - W-B Entry and start system recovery code output

        Procedure:

      1. Power switch off

      2. All doors locked

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      		 Pulse generation (See waveform 2)
      T32-10 (+5) - T32-12 (GND) G - W-B Receive mode switching signal input

        Procedure:

      1. Power switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      		 Pulse generation (See waveform 1)
      T32-11 (ASEL) - T32-12 (GND) L - W-B Communication antenna switching circuit

        Procedure:

      1. Power switch off

      2. All doors closed

      		 Below 1 V → 4.5 to 6 V → Below 1 V

  4. CHECK DOOR CONTROL RECEIVER (except 12 Pin Type)

    A01FUGCE01

    1. Disconnect the T33 door control receiver connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T33-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Reconnect the T33 door control receiver connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      T33-5 (CSEL) - T33-6 (GND) P - W-B Communication channel switching circuit

        Procedure:

      1. Power switch off

      2. All doors closed

      		 Below 1 V → 4.5 to 6 V → Below 1 V
      T33-3 (DATA) - T33-6 (GND) R - W-B Entry and start system recovery code output

        Procedure:

      1. Power switch off

      2. All doors locked

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      		 Pulse generation (See waveform 2)
      T33-2 (+5) - T33-6 (GND) G - W-B Receive mode switching signal input

        Procedure:

      1. Power switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      		 Pulse generation (See waveform 1)
      T33-4 (ASEL) - T334-6 (GND) L - W-B Communication antenna switching circuit

        Procedure:

      1. Power switch off

      2. All doors closed

      		 Below 1 V → 4.5 to 6 V → Below 1 V