MAIN BODY ECU INSTALLATION


  1. INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    Note


    • Make sure that no foreign matter gets on the connecting surfaces.

    • Do not touch the ECU connector.


    1. A01FU90E04
      Text in Illustration
      *1 Housing Sidewall
      *2 Main Body ECU (multiplex network body ECU) Guide
      *a 20°

      Insert the main body ECU (multiplex network body ECU) up to the position where it contacts the housing sidewall of the guide as shown in the illustration.

      Tech Tips

      Make sure to keep the angle 20° or more as shown in the illustration.

    2. A01FTEAE01
      Text in Illustration
      *1 Housing Sidewall
      *2 Side A Contact Portion
      *3 Junction Block Fuse

      Slide the guide of the main body ECU (multiplex network body ECU) along the housing sidewall so that it contacts the junction block fuses as shown in the illustration.

    3. A01FTA6E01
      Text in Illustration
      *1 Side A Contact Portion

      Slide the the main body ECU (multiplex network body ECU) as shown in the illustration.

    4. A01FRTYE01
      Text in Illustration
      *1 Side A Contact Portion

      While keeping the main body ECU (multiplex network body ECU) in contact with side A of the junction block (axis of rotation), rotate it downward as shown in the illustration.

    5. A01FQNFE01
      Text in Illustration
      *1 Push Area

      Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

      Note


      • Make sure to press only the push area.

      • Confirm the engagement of the main body ECU (multiplex network body ECU) and junction block by listening for the lock sound.

      Tech Tips

      If a lock sound cannot be heard, visually check the lock part engagement. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and junction block are flush.

  2. INSTALL COWL SIDE JUNCTION BLOCK LH


    1. Connect the 2 connectors.

      Note

      Be sure to connect each connector securely.

    2. Install the instrument panel cowl side junction block LH with the bolt and nuts.

      Torque:
      nut
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      bolt
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }
    3. Connect the 7 connectors.

      Note

      Be sure to connect each connector securely.

    4. w/ VGRS:


      1. Attach the 2 clamps.

      2. Connect the 5 connectors.

    5. w/o VGRS:


      1. Attach the clamp.

      2. Connect the connector.

  3. INSTALL CLEARANCE WARNING ECU ASSEMBLY


    1. for LHD:


      1. A01FUAK

        Attach the guide to install the clearance warning ECU assembly.

        Note

        Avoid any impact to the clearance warning ECU.

      2. Install the nut.

      3. Connect the connector.

    2. for RHD:

      Attach the 2 claws to install the clearance warning ECU assembly.

  4. INSTALL NO. 1 LOWER INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01FTP7

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. Attach the 3 claws to connect the hood lock control lever sub-assembly to the lower No. 1 instrument panel airbag assembly.

    6. Temporarily install the lower No. 1 instrument panel airbag assembly with the hook and pin.

    7. Install the lower No. 1 instrument panel airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  5. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for LHD)


    1. Attach the 4 clips to install the No. 1 instrument panel garnish sub-assembly.

  6. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY (for LHD)


    1. Connect the connectors.

    2. Attach the 9 clips and guide to install the No. 1 instrument panel safety pad sub-assembly.

  7. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

    A01FVEAE01
    Text in Illustration
    *1 Screw <A>
    *2 Bolt <E>

    1. Connect the connectors and attach the clamp.

    2. Attach the 6 clips to install the glove compartment door assembly.

    3. Install the 3 screws <A> and 2 bolts <E>.

  8. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect the connectors and attach the clamp.

    2. Attach the 5 clips and 2 guides to install the No. 2 instrument panel under cover sub-assembly.

  9. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL


    1. Connect the connector.

    2. Attach the 9 clips and guide to install the center instrument cluster finish panel.

  10. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. Attach the 5 clips and 2 guides to install the instrument panel finish panel end LH.

  11. INSTALL INSTRUMENT SIDE PANEL LH


    1. Attach the 7 clips to install the instrument side panel LH.

  12. INSTALL FRONT DOOR OPENING TRIM COVER LH


    1. Attach the 5 claws to install the front door opening trim cover LH.

      Note

      After installing the front door opening trim cover LH, make sure that the lip of the front door opening trim weatherstrip LH is not pinched.

  13. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 10 claws and 4 clips to install the front door scuff plate LH.

  14. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH


    1. Install the luggage compartment trim cover.

  16. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.