ULTRASONIC SENSOR (for Front Side) INSTALLATION

INSTALL ULTRASONIC SENSOR CLIP (for Corner Sensor)
1. for LH Side:
  
  Attach the claw to install the ultrasonic sensor clip to the No. 1 ultrasonic sensor.
INSTALL NO. 2 ULTRASONIC SENSOR RETAINER
Tech Tips
- Perform this step only when necessary.
- If a No. 2 ultrasonic sensor retainer has been removed, replace it with a new one. Install the No. 1 ultrasonic sensor with a new No. 2 ultrasonic sensor retainer as a set to the front bumper assembly.
- Use the same procedure for all No. 2 ultrasonic sensor retainers.
1. Attach the 2 claws and install 2 No. 2 ultrasonic sensor retainers to the No. 1 ultrasonic sensor.
2. Clean the front bumper cover surface.
  1. Remove the double-sided tape from the front bumper cover.
  2. Wipe off any tape adhesive residue with cleaner.
3. Text in Illustration
  
  *a Primer
  
  Using a brush or felt, apply primer or equivalent to the No. 2 ultrasonic sensor retainer installation area.
  Note
  
  Use a clean brush or felt.
  
  Do not touch the front bumper assembly until the primer has dried.
4. Peel off the release paper from the 2 No. 2 ultrasonic sensor retainers.
5. Text in Illustration
  
  *a Protrusion of the mark
  
  Align the No. 2 ultrasonic sensor retainer with No. 1 ultrasonic sensor with the mark on the front bumper cover and install it as shown in the illustration.
  
  Note
  
  The double sided tape of a No. 2 ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the No. 2 ultrasonic sensor retainer with a new one when reattachment is necessary.
  Tech Tips
  
  Align the connector with the protrusion of the mark and connect it.
  
  Press on the areas indicated by the arrows in the illustration with a force of 30 N (3.0 kgf) for 3 seconds and install the No. 2 ultrasonic sensor retainer firmly so that there is no clearance between the No. 2 ultrasonic sensor retainer and front bumper cover.
INSTALL NO. 1 ULTRASONIC SENSOR RETAINER
Tech Tips
- Perform this step only when necessary.
- If a No. 1 ultrasonic sensor retainer has been removed, replace it with a new one. Install the No. 1 ultrasonic sensor with a new No. 1 ultrasonic sensor retainer as a set to the front bumper assembly.
- Use the same procedure for all No. 1 ultrasonic sensor retainers.
1. Attach the 2 claws and install 2 No. 1 ultrasonic sensor retainers to the No. 1 ultrasonic sensor.
2. Clean the front bumper cover surface.
  1. Remove the double-sided tape from the front bumper cover.
  2. Wipe off any tape adhesive residue with cleaner.
3. Text in Illustration
  
  *a Primer
  
  Using a brush or felt, apply primer or equivalent to the No. 1 ultrasonic sensor retainer installation area.
  Note
  
  Use a clean brush or felt.
  
  Do not touch the front bumper assembly until the primer has dried.
4. Peel off the release paper from the 2 No. 1 ultrasonic sensor retainers.
5. Text in Illustration
  
  *a Protrusion of the mark
  
  Align the No. 1 ultrasonic sensor retainer with No. 1 ultrasonic sensor with the mark on the front bumper cover and install it as shown in the illustration.
  
  Note
  
  The double sided tape of a No. 1 ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the No. 1 ultrasonic sensor retainer with a new one when reattachment is necessary.
  Tech Tips
  
  Align the connector with the protrusion of the mark and connect it.
  
  Press on the areas indicated by the arrows in the illustration with a force of 30 N (3.0 kgf) for 3 seconds and install the No. 1 ultrasonic sensor retainer firmly so that there is no clearance between the No. 1 ultrasonic sensor retainer and front bumper cover.
INSTALL NO. 4 ENGINE ROOM WIRE
1. for Sport Package:
  
  Attach the 10 clamps to install the No. 4 engine room wire.
2. except Sport Package:
  
  Attach the 11 clamps to install the No. 4 engine room wire.
3. Connect the 4 connectors.
INSTALL FRONT BUMPER COVER
1. for Sport Package:
  
  Click here
2. except Sport Package:
  
  Click here