BLIND SPOT MONITOR SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.

    5. Read the Data List according to the display on the GTS.


      • *: w/ Variable Gear Ration Steering System

      Blind Spot Monitor Master
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Main Switch Blind spot monitor main switch (integration control and panel assembly) / OFF or ON

      ON: Blind spot monitor main switch (integration control and panel assembly) on

      OFF: Blind spot monitor main switch (integration control and panel assembly) off

      		 -
      Master Side Turn Switch Master side turn switch / OFF or ON

      ON: Right turn switch on

      OFF: Right turn switch off

      		 For models that receive signals via CAN, OFF is always displayed.
      Warning Indicator Turning on (Master) State of the outer rear view mirror indicator RH turning on / OFF or ON

      OFF: The following conditions are not met


      • ON: All of the following conditions are met


        • Not during initial check

        • Vehicle detected in right hand side warning area

        • Right turn signal: off

        • Vehicle speed 40 km/h (25 mph) or more

        • Shift lever in any position except R

        • Blind spot monitor warning light not illuminated

      		 -
      Warning Indicator Flashing (Master) State of the outer rear view mirror indicator RH flashing / OFF or ON

      OFF: The following conditions are not met


      • ON: All of the following conditions are met


        • Not during initial check


        • Vehicle detected in right hand side warning area


        • Right turn signal: on


        • Vehicle speed 40 km/h (25 mph) or more


        • Shift lever in any position except R


        • Blind spot monitor warning light not illuminated

      		 -
      Turn Switch State Master side, slave side state of the turn SW / master ON, slave ON or OFF

      Master ON: Right turn switch on

      Slave ON: Left turn switch on

      OFF: Switch not operated

      		 -
      Master Side Turn Signal State of the master side turn signal / OFF or ON

      ON: Right turn signal received

      OFF: Right turn signal not received

      		 -
      Reverse State of the shift position R signal / OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      		 -
      Vehicle Speed Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering angle sensor / Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      		 -
      VGRS Relative Angle* Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V 11 to 14 V -
      HV Flag Hybrid vehicle / OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      		 -
      VGRS Flag VGRS installed / OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      		 -
      Main SW Inspection Completeness Flag Completion of inspection for blind spot monitor main switch (integration control and panel assembly) / Incompl or compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      		 Changes to Compl when the blind spot monitor main switch (integration control and panel assembly) is changed from off to on during Test Mode.
      Beam Axis Inspection Completeness Flag Completion of beam axis inspection / Incompl or compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      		 Changes to Compl when Test Mode has been entered.
      Destination Undefined Flag Destination determination / Unfixed or Fixed

      Unfixed: Sensor destination information not determined

      Fixed: Sensor destination information determined according to CAN destination information

      		 -
      Number of DTC Number of DTC / Min.: 0, Max.: 255

      When system is normal: 0

      when a malfunction is detected: More than 0

      		 -
      Blind Spot Monitor Slave
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Slave Side Turn Switch Slave side turn switch / OFF or ON

      ON: Left turn switch on

      OFF: Left turn switch off

      		 For models that receive signals via CAN, OFF is always displayed.
      Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator LH turning on / OFF or ON

      OFF: The following conditions are not met


      • ON: All of the following conditions are met


        • Not during initial check

        • Vehicle detected in left hand side warning area

        • Left turn signal: off

        • Vehicle speed 40 km/h (25 mph) or more

        • Shift lever in any position except R

        • Blind spot monitor warning light not illuminated

      		 -
      Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator LH flashing / OFF or ON

      OFF: The following conditions are not met


      • ON: All of the following conditions are met


        • Not during initial check

        • Vehicle detected in left hand side warning area

        • Vehicle speed 40 km/h (25 mph) or more

        • Left turn signal: on

        • Shift lever in any position except R

        • Blind spot monitor warning light not illuminated

      		 -
      Turn Switch State Master side, slave side state of the turn SW / master ON or slave ON or OFF

      Master ON: Right turn switch on

      Slave ON: Left turn switch on

      OFF: Switch not operated

      		 -
      Slave Side Turn Signal State of the slave side turn signal / OFF or ON

      ON: Left turn signal received

      OFF: Left turn signal not received

      		 -
      Reverse State of the shift position R signal / OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      		 -
      Vehicle Speed Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering angle sensor / Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      		 -
      VGRS Relative Angle* Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V 11 to 14 V -
      HV Flag Hybrid vehicle / OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      		 -
      VGRS Flag VGRS installed / OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      		 -
      Beam Axis Inspection Completeness Flag Completion of beam axis inspection / Incompl or compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      		 Changes to Compl when Test Mode has been entered.
      Destination Undefined Flag Destination determination / Unfixed or Fixed

      Unfixed: Sensor destination information not determined

      Fixed: Sensor destination information determined according to CAN destination information

      		 -
      Number of DTC Number of DTC / Min.: 0, Max.: 255

      When system is normal: 0

      when a malfunction is detected: More than 0

      		 -