AUDIO AND VISUAL SYSTEM Radio Broadcast cannot be Received or Poor Reception

WIRING DIAGRAM

A01FTKXE03

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    1. Check the radio automatic station search function by activating it.

      OK
      Automatic station search function stops on a station.

    NG

    CHECK OPTIONAL COMPONENTS Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  2. CHECK OPTIONAL COMPONENTS


    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Note

      Do not remove optional components without permission of the customer.

      OK
      Optional components are installed.

    NG

    REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

    OK

  3. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    1. A01FVI8

      Remove the antenna connector from the multi-media module receiver assembly.

    2. Turn the power switch on (ACC) with the multi-media module receiver assembly connector connected.

    3. Turn on the radio and turn into AM mode.

    4. Place a screwdriver, thin wire or other metal object on the multi-media module receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK
      Noise occurs.

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  4. CHECK BACK WINDOW GLASS (WINDOW GLASS ANTENNA WIRE)


    1. Inspect the back window glass (window glass antenna wire) Click here.


    NG

    REPAIR BACK WINDOW GLASS (WINDOW GLASS ANTENNA WIRE) Click here

    OK

  5. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    1. A01FTJYE30
      Text in Illustration
      *a

      Component without harness connected

      (Multi-media Module Receiver Assembly)

      Disconnect the multi-media module receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      RA-5 (ANT+) - Body ground Power switch on (ACC), radio switch on and FM or AM selected 11 to 14 V

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  6. CHECK ANTENNA CORD SUB-ASSEMBLY


    1. A01FVLFE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Multi-media Module Receiver Assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)

      Disconnect the antenna connector from the multi-media module receiver assembly.

    2. Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      RA-3 (MAIN) - 6 Always Below 1 Ω
      RA-1 (SUB) - 5 Always Below 1 Ω
      RA-5 (ANT+) - 3 Always Below 1 Ω
      RA-3 (MAIN) - Body ground Always 10 kΩ or higher
      RA-1 (SUB) - Body ground Always 10 kΩ or higher
      RA-5 (ANT+) - Body ground Always 10 kΩ or higher

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  7. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. A01FV2JE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to Amplifier Antenna Assembly)

      Disconnect the antenna connector from the antenna cord sub-assembly.

    2. Disconnect the antenna connector from the amplifier antenna assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      6 - 1 Always Below 1 Ω
      5 - 2 Always Below 1 Ω
      3 - 3 Always Below 1 Ω
      6 - Body ground Always 10 kΩ or higher
      5 - Body ground Always 10 kΩ or higher
      3 - Body ground Always 10 kΩ or higher

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  8. CHECK AMPLIFIER ANTENNA ASSEMBLY


    1. Replace the amplifier antenna assembly and check if radio broadcasts can be received normally Click here.

      OK
      Radio broadcasts can be received normally.

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

    END (AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)