PARKING BRAKE ASSEMBLY REASSEMBLY

Note


  • Use the same procedure for the LH side and RH side.

  • The procedures listed below are for the LH side.


  1. APPLY HIGH-TEMPERATURE GREASE


    1. A01FQH4

      Apply a light coat of high-temperature grease to the areas of the backing plate which make contact with the shoe as shown in the illustration.

  2. INSTALL PARKING BRAKE CABLE SUPPORT BRACKET


    1. A01FQ7X

      Install the parking brake cable support bracket.

  3. INSTALL PARKING BRAKE ANCHOR BLOCK SUB-ASSEMBLY


    1. A01FUMN

      Install the parking brake anchor block and cable support bracket with the 2 nuts.

      Torque:
      76 N*m  { 770 kgf*cm, 56 ft.*lbf }

  4. CONNECT PARKING BRAKE CABLE


    1. A01FR1N

      Connect the parking brake cable with the nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A01FSM5E01

      Using SST, install the No. 1 parking brake shoe with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.

      SST
      09718-00011

      Tech Tips

      Use the service hole to retain the parking brake shoe hold down spring pin with your finger.

  6. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A01FRHTE01

      Using SST, install the No. 2 parking brake shoe with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.

      SST
      09718-00011

      Tech Tips

      Use the service hole to retain the parking brake shoe hold down spring pin with your finger.

  7. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A01FVO1

      Apply high-temperature grease to the threads and all joining areas of the parking brake shoe adjusting screw set.

      Text in Illustration
      A01FVNL High-temperature grease
    2. A01FQO1

      Install the parking brake shoe adjusting screw set.

  8. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01FTJDE01

      Install the No. 1 parking brake shoe return tension spring.

      SST
      09703-30011

  9. INSTALL PARKING BRAKE SHOE LEVER


    1. A01FQIEE01
      Text in Illustration
      *1 Parking Brake Anchor Block Sub-assembly
      *2 Pin
      *a for LH
      *b for RH

      Apply a thin layer of high-temperature grease to the areas where the parking brake shoe lever contacts the parking brake anchor block.

    2. Install the parking brake shoe lever to the parking brake cable.

      Note

      Take care to install the correct parking brake shoe lever because the direction of the pin is different between the left and right.

    3. A01FVMUE01
      Text in Illustration
      *1 Inner Cable
      *2 Parking Brake Shoe Lever

      Check that the parking brake inner cable and parking brake shoe lever are securely connected by trying to pull them apart.

    4. A01FR6Y

      With the vehicle on the ground, check that the gap between the parking brake cable and drive shaft, and the gap between the parking brake cable and shaft boot are 10 mm (0.394 in.) or more.

      Tech Tips

      Make sure that the cable is not twisted.

  10. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01FRG3E01

      Install the No. 2 parking brake shoe return tension spring.

      SST
      09703-30011

  11. CHECK PARKING BRAKE INSTALLATION


    1. Make sure that all the parts are installed properly.

      A01FQMQE01
      Text in Illustration
      *a for LH *b for RH
      *c Front - -

      If necessary, reinstall the parts properly.

  12. INSTALL REAR DISC

    Click here

  13. ADJUST PARKING BRAKE

    Click here

  14. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  15. PERFORM PARKING BRAKE SHOE BEDDING

    Click here