FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. A01FVAZE01

      Engage the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.

    2. Fully tighten the bolt <A> first, then the bolt <B> to install the front shoulder belt anchor adjuster assembly.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL FRONT SEAT BELT RETRACTOR COVER LH


    1. Install the front seat belt retractor cover LH so that the arrow on the bottom points upwards.

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01FSIZE01
      Text in Illustration
      *1 Pretensioner Connector

      Temporarily install the front seat outer belt assembly LH with the 2 bolts.

    2. Fully tighten the bolt <A> first, then the bolt <B> to install the front seat outer belt assembly.

      Torque:
      Bolt <A>
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
      Bolt <B>
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    4. Connect the connector (w/o Pre-collision System) or 2 connectors (w/ Pre-collision System).

    5. Connect the shoulder anchor of the front seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  4. INSTALL UPPER CENTER PILLAR GARNISH LH


    1. Pass the front seat outer belt floor anchor through the upper center pillar garnish LH.

    2. Attach the clip to install the upper center pillar garnish LH.

    3. Install the 2 screws.

      Note

      After installing the upper center pillar garnish LH, make sure that the lip of the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH is not pinched.

  5. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. Attach the 5 clips and 2 guides.

    2. While pulling both sides of the lower center garnish outward by hand, set the garnish in place, and then attach the 2 claws to install the lower center pillar garnish LH.

      Note

      After installing the lower center pillar garnish LH, make sure that the lip of the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH is not pinched.

  6. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. Operate the power seat switch assembly and move the front seat assembly so that the nut for the anchor of the front seat outer belt assembly LH can be installed.

    2. A01FRVME01
      Text in Illustration
      *1 Protruding Part

      Connect the anchor of the front seat outer belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor of the front seat outer belt assembly LH to overlap the protruding part of the front seat assembly.

    3. Attach the 6 hooks to install the seat belt anchor cover cap LH.

    4. Check it the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  8. INSTALL REAR DOOR SCUFF PLATE LH


    1. Attach the 10 claws and 3 clips to install the rear door scuff plate LH.

  9. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 10 claws and 4 clips to install the front door scuff plate LH.

  10. INSPECT SRS WARNING LIGHT

    Click here

  11. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH


    1. Install the luggage compartment trim cover.

  12. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.