AIR CONDITIONING SYSTEM, Diagnostic DTC:B1454/54

DTC Code DTC Name
B1454/54 Passenger Side Air Outlet Damper COOL Control Servo Motor Circuit

DESCRIPTION


The No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*1 or No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*2 sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*1 or No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*2 to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the front passenger side lower is controlled.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

DTC Code DTC Detection Condition Trouble Area
B1454/54 Air mix damper position does not change even if air conditioning amplifier assembly operates No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*1 or No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*2

  • No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*1

  • No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*2

  • Air conditioning harness assembly

  • Air conditioning amplifier assembly

WIRING DIAGRAM

A01FT5RE82

INSPECTION PROCEDURE

Note


  • Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.

  • When the auxiliary battery is disconnected, or a servo motor or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization Click here.

  • Before disconnecting the cable form the negative (-) battery terminal or replacing the air conditioning amplifier assembly, record the last operation state of the air conditioning for each transmitter. After replacement, it is necessary to perform memory registration for each transmitter Click here.

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1454/54 is not output A
      DTC B1454/54 is output B
      DTC B1454/54 and B1497/97 are output C

    B

    READ VALUE USING GTS (COOL A/M SERVO ACTUAL PULSE[P]) Click here

    C

    GO TO DTC B1497/97 Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  2. READ VALUE USING GTS (COOL A/M SERVO ACTUAL PULSE[P])


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Data List Click here.

    5. Check the value(s) by referring to the table below.

      Air Conditioner
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      COOL A/M Servo Actual Pulse(P)

      No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix) actual target pulse*1 /

      Min.: 128, Max.: 383

      MAX. COLD*3: 254 (pulse)

      MAX. HOT*4: 360 (pulse)

      		 -

      No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix) actual pulse*2 /

      Min.: 128, Max.: 383

      MAX. COLD*3: 254 (pulse)

      MAX. HOT*4: 360 (pulse)

      		 -

      • *1: for LHD

      • *2: for RHD

      • *3: Set temperature: LO

      • *4: Set temperature: HI

      OK
      The display is as specified in the Normal Condition column.
      Result
      Result Proceed to
      NG A
      OK (When troubleshooting according to Problem Symptoms Table) B
      OK (When troubleshooting according to the DTC) C

    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    A

  3. PERFORM ACTIVE TEST USING GTS (COOL A/M SERVO PULSE[P])


    • *1: for LHD

    • *2: for RHD


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Active Test Click here.

    5. Check the operation by referring to the table below.

      Air Conditioner
      Tester Display Test Part Control Range Diagnostic Note
      Cool A/M Servo Pulse(P) No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*1 Min.: 128, Max.: 383 Operates between 254 to 360 pulses
      No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*2 Min.: 128, Max.: 383 Operates between 254 to 360 pulses
      OK
      The No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*1 or No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*2 pulse signal changes according to the target pulse specified by the Active Test.

    NG

    CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (FRONT PASSENGER SIDE LOWER AIR MIX) OR NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (FRONT PASSENGER SIDE LOWER AIR MIX) Click here

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  4. CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (FRONT PASSENGER SIDE LOWER AIR MIX) OR NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (FRONT PASSENGER SIDE LOWER AIR MIX)


    1. Replace the No. 3 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*1 or No. 4 air conditioning radiator damper servo sub-assembly (front passenger side lower air mix)*2 Click here.


      • *1: for LHD

      • *2: for RHD

      Tech Tips

      Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1454/54 is not output (for LHD) A
      DTC B1454/54 is not output (for RHD) B
      DTC B1454/54 is output C

    B

    END (NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY [FRONT PASSENGER SIDE LOWER AIR MIX] WAS DEFECTIVE)

    C

    CHECK AIR CONDITIONING HARNESS ASSEMBLY Click here

    A

    END (NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY [FRONT PASSENGER SIDE LOWER AIR MIX] WAS DEFECTIVE)

  5. CHECK AIR CONDITIONING HARNESS ASSEMBLY


    1. Replace the air conditioning harness assembly Click here.

      Tech Tips

      Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.

    2. Check for DTCs Click here.

      OK
      DTC B1454/54 is not output.

    NG

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    OK

    END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)