WATER PUMP WITH MOTOR INSTALLATION


  1. INSTALL INVERTER WATER PUMP WITH MOTOR ASSEMBLY


    1. Install the water pump with motor with the 3 bolts.

      Torque:
      6.1 N*m  { 62 kgf*cm, 54 in.*lbf }

      Note

      Do not hold the water pump with motor assembly by the connector terminals when removing or installing it.

  2. INSTALL HV WATER PUMP BRACKET SUB-ASSEMBLY


    1. Install the HV water pump bracket with bolt.

      Torque:
      100 N*m  { 1020 kgf*cm, 74 ft.*lbf }
    2. A01FUJZE01
      Text in Illustration
      *a Upper
      *b Front
      *c 90°
      *d 30°
      *e 45°
      *f LH Side

      for LHD:

      Connect the 2 water hoses.

      Note


      • Make sure that the clip is positioned as shown in the illustration.

      • Do not remove the pieces of cloth or plastic bags from the pipe and disconnected hose until installation.

    3. A01FVHKE01
      Text in Illustration
      *a Upper
      *b Front
      *c 90°
      *d 30°
      *e 45°
      *f LH Side

      for RHD:

      Connect the 2 water hoses and attach the clamp.

      Note


      • Make sure that the clip is positioned as shown in the illustration.

      • Do not remove the pieces of cloth or plastic bags from the pipe and disconnected hose until installation.

    4. Attach the clamp and connect the connector.

  3. ADD COOLANT (for Inverter)

    Note


    • Do not reuse the drained coolant because it may contain foreign objects.

    • If the vehicle is driven with air in the inverter cooling system, damage may occur and the following DTCs may be set.

      DTC Code Detection Item
      P0A04-725 Motor Electronics Coolant Temperature Sensor Circuit Intermittent
      P0A01-726 Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
      P0A08-264 DC / DC Converter Status Circuit
      P0A78-284 Drive Motor "A" Inverter Performance
      P0A78-286 Drive Motor "A" Inverter Performance
      P0A7A-322 Generator Inverter Performance
      P0A7A-324 Generator Inverter Performance
      P0A93-346 Inverter Cooling System Performance
      P0A94-553 DC / DC Converter Performance
      P0A94-557 DC / DC Converter Performance
      P0AF1-276 Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic
      P0AEE-277 Motor Inverter Temperature Sensor "A" Circuit Range / Performance
      P0BD0-314 Generator Inverter Temperature Sensor Circuit Range / Erratic
      P0BCD-315 Generator Inverter Temperature Sensor Circuit Range / Performance
      P0C3C-625 DC / DC Converter Temperature Sensor "A" Intermittent / Erratic
      P0C39-626 DC / DC Converter Temperature Sensor "A" Range / Performance
      P0C41-627 DC / DC Converter Temperature Sensor "B" Intermittent / Erratic
      P0C3E-628 DC / DC Converter Temperature Sensor "B" Range / Performance
      P0C73-776 Motor Electronics Coolant Pump "A" Control Performance

    1. Slowly pour coolant into the reservoir tank until it reaches the FULL line.

      Standard Capacity
      Item Specified Condition
      for LHD 3.1 liters (3.3 US qts, 2.7 Imp. qts.)
      for RHD 2.9 liters (3.0 US qts, 2.6 Imp. qts.)

      Note

      To prevent foreign matter such as dust or dirt from entering the cooling system, make sure to confirm that the container used to add coolant is clean and free of foreign matter such as dust or dirt.

    2. When using the GTS:


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

      4. Keep the coolant at the FULL line in the reservoir tank to compensate for the drop in coolant level when the air bleeds.

        Standard
        Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reservoir tank improves.

        Tech Tips


        • If free spinning of the inverter water pump is detected for approximately 5 seconds, failsafe control will be activated to suspend the operation of the pump for approximately 15 seconds and resume operation for approximately 4 seconds repeatedly. Operation of the inverter water pump will return to normal if coolant is added.

        • Loud noise made by the inverter water pump and poor circulation of coolant in the reservoir tank indicates that there is air in the cooling system.

    3. When not using the GTS:


      1. Turn the power switch on (READY).[*1]

      2. Turn the power switch off and add coolant to the FULL line because the coolant level drops as the air bleeds.[*2]

        Note


        • Be sure to turn the power switch off before adding SLLC.

        • Do not work on the components in the engine compartment while the vehicle is in the READY-on state because the engine is in intermittent operation.

      3. Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.

        Standard
        Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reservoir tank improves.

        Tech Tips

        Loud noise made by the inverter water pump and poor circulation of coolant in the reservoir tank indicates that there is air in the cooling system.

    4. After the air is completely bled from the cooling system, tighten the reservoir tank cap.

    5. Add coolant to the FULL line of the reservoir tank.

  4. INSPECT FOR COOLANT LEAK (for Inverter)


    1. Remove the reservoir tank cap (for inverter).

      CAUTION:

      To avoid the danger of being burned, do not remove the reservoir tank cap while the coolant for the inverter is still hot.

    2. A01FVL9

      Install the radiator cap tester.

    3. Pump the radiator cap tester to 137 kPa (1.4 kgf/ cm2, 20 psi), and then check that the pressure does not drop.

      Tech Tips

      If the pressure drops, check the hoses, radiator, water pump, inverter with converter, and hybrid vehicle transaxle assembly for leaks.

    4. Reinstall the reservoir tank cap (for inverter).

  5. INSTALL NO. 2 ENGINE UNDER COVER


    1. Install the No. 2 engine under cover with the 4 screws and 2 grommets.

  6. INSTALL FRONT SUSPENSION MEMBER BRACE


    1. Install the front suspension member brace with the clip and 4 bolts.

      Torque:
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }

  7. INSTALL ENGINE UNDER COVER


    1. Install the engine under cover with the 13 screws and 3 clips.

  8. INSTALL NO. 1 AIR CLEANER INLET


    1. Install the No. 1 air cleaner inlet with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  9. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 7 clips.

  10. INSTALL ENGINE ROOM SIDE COVER


    1. Install the engine room side cover with the 4 clips.