FRONT UPPER SUSPENSION ARM INSTALLATION


  1. INSTALL FRONT SUSPENSION UPPER ARM ASSEMBLY


    1. Install the front suspension upper arm with the 2 bolts.

      Torque:
      49 N*m  { 500 kgf*cm, 36 ft.*lbf }

  2. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. Install the front shock absorber with front coil spring on the vehicle by tightening the 3 nuts on the suspension support side.

      Torque:
      67 N*m  { 683 kgf*cm, 49 ft.*lbf }

    2. Insert the bolt from the rear of the vehicle, and install the front shock absorber lower side on the front suspension lower arm.

    3. Temporarily tighten the nut while holding the bolt.

    4. Tighten a new lock nut.

      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  3. INSTALL ABSORBER CONTROL ACTUATOR


    1. A01FRBHE08
      Text in Illustration
      *a 40°

      Check that the control rod of the front shock absorber is in the position shown in the illustration.

      Note

      If the control rod is not in the position shown in the illustration, turn the control rod to adjust the position before installing the absorber control actuator.

    2. A01FU6HE01
      Text in Illustration
      *a 40°

      Install the absorber control actuator to the actuator support bracket.

    3. Turn the actuator clockwise 40° until a click is felt.

      Note


      • Before turning the actuator, make sure to check that the actuator output shaft and control rod are securely connected.

      • Do not turn the actuator more than 40°.

      • Do not drop the absorber control actuator. If it is dropped, replace it with a new one.

  4. INSTALL UPPER SHOCK ABSORBER CAP


    1. Connect the connector.

    2. Install the upper shock absorber cap with the 3 nuts.

      Torque:
      20 N*m  { 200 kgf*cm, 14 ft.*lbf }

  5. CONNECT FRONT SUSPENSION UPPER ARM ASSEMBLY


    1. Install the steering knuckle to the front suspension upper arm, and tighten it with the castle nut.

      Torque:
      87 N*m  { 887 kgf*cm, 64 ft.*lbf }

    2. Install a new clip to the steering knuckle.

      Note

      Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.

  6. CONNECT SKID CONTROL SENSOR WIRE


    1. Install the skid control sensor to the front shock absorber with coil spring with the bolt.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

      Note


      • Do not twist the skid control sensor while installing.

      • Be careful not to deform the bracket of the front shock absorber with coil spring when installing the bolt.

  7. STABILIZE SUSPENSION


    1. A01FTDK

      Install the front wheels.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    2. Lower the vehicle and bounce it up and down several times to stabilize the front suspension.

    3. Remove the front wheels.

    4. Jack up the front suspension lower arm placing a wooden block in between. Apply a load to the front suspension so that the front suspension lower arm is placed in a horizontal position.

  8. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. Fully tighten the bolt on the lower side of the front shock absorber while holding the nut.

      Torque:
      108 N*m  { 1101 kgf*cm, 80 ft.*lbf }

  9. INSTALL FRONT WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  10. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here