СИСТЕМА АВТОМАТИЧЕСКОЙ ТРАНСМИССИИ РЕЖИМЫ DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG) position.

    5. Turn the GTS on.

    6. Select the item "Powertrain / Engine and ECT / Data List".

    7. According to the display on the GTS, read the "Data List".

      Engine and ECT
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      N Range Status

      Shift lever N status/

      ON or OFF

      • ON: Shift lever in P or N

      • OFF: Shift lever not in P or N

      		 -
      Neutral Position SW Signal

      PNP switch status/

      ON or OFF

      • ON: Shift lever in P or N

      • OFF: Shift lever not in P or N

      When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      Stop Light Switch

      Stop light switch status/

      ON or OFF

      • ON: Brake pedal depressed

      • OFF: Brake pedal released

      		 -
      SPD (NT)

      Input shaft speed/

      Min.: 0 rpm

      Max.: 12750 rpm

      • Lock-up ON (after warming up engine): Input turbine speed (NT) equal to engine speed

      • Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed

      		 Data is displayed in increments of 50 rpm.
      SPD (SP2)

      Output shaft speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      		 Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) -
      Shift SW Status (P Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever in P

      • OFF: Shift lever not in P

      When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      Kick Down Switch Status

      Kick down switch status*1/

      ON or OFF

      • ON: Accelerator pedal is depressed all the down

      • OFF: Accelerator pedal is released

      		 -
      Pattern Switch (PWR/M)

      Sport mode status/

      ON or OFF

      • ON: Sport mode on

      • OFF: Sport mode off

      		 -
      Shift SW Status (R Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever in R

      • OFF: Shift lever not in R

      When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      Shift SW Status (N Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever in N

      • OFF: Shift lever not in N

      When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      Shift SW Status (N, P Range) Supported

      Status of PNP switch (N or P) supported/

      Supp or Unsupp

      		 - -
      Shift SW Status (N, P Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever not in P or N

      • OFF: Shift lever in P or N

      		 -
      Sports Shift Up SW

      Sport shift up switch status/

      ON or OFF

      • ON: Shift lever held in "+" (up-shift)

      • OFF: Shift lever not held in "+" (up-shift)

      		 -

      • ON: "+" shift paddle operated and held (up-shift)

      • OFF: "+" shift paddle not operated (up-shift)
      Sports Shift Down SW

      Sport shift down switch status/

      ON or OFF

      • ON: Shift lever held in "-" (down-shift)

      • OFF: Shift lever not held in "-" (down-shift)

      		 -

      • ON: "-" shift paddle operated and held (down-shift)

      • OFF: "-" shift paddle not operated (down-shift)
      Sports Mode Selection SW

      Sport mode select switch status/

      ON or OFF

      • ON: Shift lever in M, "+" or "-"

      • OFF: Shift lever not in M, "+" or "-"

      		 -
      Snow Switch Status

      Combination switch (SNOW) status*2/

      ON or OFF

      • ON: Combination switch (SNOW) pushed

      • OFF: Combination switch (SNOW) not pushed

      		 -
      Shift SW Status (D Range)

      PNP switch status/

      ON or OFF

      • ON: Shift lever in D, M, "+" or "-"

      • OFF: Shift lever not in D, M, "+" or "-"

      When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      A/T Oil Temperature 1

      No. 1 ATF temperature sensor value/

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      • After stall test: Approximately 80°C (176°F)

      • Equal to ambient temperature when engine cold

      		 If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
      Normal Mode Switch

      Combination switch (NORMAL) status/

      ON or OFF

      • ON: Combination switch being pushed and held

      • OFF: Combination switch not pushed

      		 -
      Sports Mode Switch

      Combination switch (SPORT) status/

      ON or OFF

      • ON: Combination switch being turned and held at SPORT position

      • OFF: Combination switch not turned

      		 -
      ECO Switch

      ECO mode status/

      ON or OFF

      • ON: ECO mode on

      • OFF: ECO mode off

      		 -
      Lock Up

      Lock-up/

      ON or OFF

      • ON: Lock-up operating

      • OFF: Lock-up not operating

      		 -
      Shift Status

      ECM gear shift command/

      1st, 2nd, 3rd, 4th, 5th or 6th

      		 1st, 2nd, 3rd, 4th, 5th or 6th: Shift lever in D or M -
      SLT Solenoid Status

      Shift solenoid SLT status/

      ON or OFF

      • OFF: Accelerator pedal depressed

      • ON: Accelerator pedal released

      		 -
      SLU Solenoid Status

      Shift solenoid SLU status/

      ON or OFF

      • ON: Shift solenoid SLU operating

      • OFF: Shift solenoid SLU not operating

      		 -
      Snow or 2nd Start Mode

      Snow mode status*2/

      ON or OFF

      • ON: Snow mode on

      • OFF: Snow mode off

      		 -
      AT Fluid

      Flex lock-up judder judgment/

      ON or OFF

      • ON: Judder judgment occurs

      • OFF: Judder judgment does not occur

      		 -

      • *1: w/ Kick down switch assembly

      • *2: w/ SNOW switch

  2. ACTIVE TEST

    Tech Tips

    Using GTS to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG) position.

    5. Turn the GTS on.

    6. Select the item "Powertrain / Engine and ECT / Active Test".

    7. According to the display on GTS, perform the "Active Test".

      Engine and ECT
      Tester Display Test Part Control Range Diagnostic Note
      Activate the Solenoid (SLU) Operate shift solenoid valve SLU ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SLT)* Operate shift solenoid valve SLT and raise line pressure

      ON or OFF

      Tech Tips


      • OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" performed, ECM commands shift solenoid valve SLT to turn off)

      • ON: No action (normal operation)

      [Vehicle Condition]


      • Vehicle stopped

      • Engine idling
      Activate the Solenoid (S1) Operate shift solenoid valve S1 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (S2) Operate shift solenoid valve S2 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (S3) Operate shift solenoid valve S3 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (S4) Operate shift solenoid valve S4 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Lock Up Control shift solenoid valve SLU to set automatic transmission to lock-up ON or OFF

      Possible to check shift solenoid valve SLU operation.

      [Vehicle Condition]


      • Throttle valve opening angle: Less than 35%

      • Vehicle speed: 60 km/h (36 mph) or more
      Control the Shift Position Operate shift solenoid valves and set each shift position

      • Press "→" button: Shift up

      • Press "←" button: Shift down

      Possible to check operation of the shift solenoid valves.

      [Vehicle Condition]

      50 km/h (30 mph) or less
      Activate the Solenoid (SR) Operate shift solenoid valve SR ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL1) Operate shift solenoid valve SL1 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL2) Operate shift solenoid valve SL2 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N

      *: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST Click here as well.

      Tech Tips

      The pressure values in Active Test and HYDRAULIC TEST are different from each other.