REAR DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH


    1. attach the 4 claws to install the rear door belt moulding.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.

    2. Connect the cable to the negative (-) battery terminal.

    3. Operate the rear door window regulator so that the rear door glass can be installed.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Remove the rear power window regulator switch assembly with rear door armrest base panel.

    6. Install the front side of the rear door glass run.

    7. A01FE12E01
      Text in Illustration
      *1 MP Grease

      Apply MP grease to the sliding area of the rear door glass channel as shown in the illustration.

      Standard
      Area Specified Condition
      A 122 mm (4.80 in.)
      B 35 mm (1.38 in.)
    8. A01FF93

      Install the rear door glass channel to the rear door window regulator as shown in the illustration.

      Note

      Do not damage the door glass.

  3. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. Install the rear door quarter window glass.

  4. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    1. Align the rear door glass run with the rear door rear lower window frame.

    2. Insert the rear door rear lower window frame together with the rear door glass run into the front door panel.

    3. Partially install the screw and 2 bolts.

    4. Install the upper side of the rear door glass run.

  5. INSTALL REAR DOOR GLASS RUN LH


    1. Finish installing the rear door glass run.

  6. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the rear door panel.

    2. A01FEWQE01
      Text in Illustration
      *a Reference Point

      Pass the rear door inside locking cable and rear door lock remote control cable through a new rear door service hole cover, and then attach the rear door service hole cover using the reference points on the rear door panel.

      Note


      • Securely install the rear door service hole cover to prevent wrinkles and air bubbles.

      • There should be no wrinkles or folds after installing the rear door service hole cover.

      • After installing the rear door service hole cover, check the seal quality.

  7. INSTALL REAR NO. 2 SPEAKER ASSEMBLY


    1. Attach the clip to install the rear No. 2 speaker assembly.

      Note

      Do not touch the cone of the speaker.

    2. Connect the connector.

  8. INSTALL REAR DOOR ARMREST SET BRACKET LH


    1. Install the rear door armrest set bracket with the 2 screws.

  9. INSTALL REAR DOOR FRAME GARNISH LH


    1. Attach the 2 clips to install the rear door frame garnish.

  10. INSTALL REAR SIDE CURTAIN ASSEMBLY LH (w/ Rear Sunshade)


    1. Attach the 2 clips and 4 claws to install the rear side curtain.

  11. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. Install the rear door inner glass weatherstrip.

  12. INSTALL REAR DOOR TRIM COVER LH


    1. Attach the 6 clips to install the rear door trim cover.

  13. INSTALL REAR DOOR NO. 1 STIFFENER CUSHION


    1. Install the rear door No. 1 stiffener cushion.

  14. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. Connect the rear door lock remote control cable and rear door inside locking cable.

    2. Connect each connector.

    3. A01FGYPE01
      Text in Illustration
      *1 Reference Boss

      Attach the 3 claws to install the rear door trim board to the rear door inner glass weatherstrip.

    4. Attach the reference boss in the direction indicated by the arrow in the illustration.

    5. Attach the 8 clips to install the rear door trim board.

    6. Install the 3 screws.

  15. INSTALL REAR DOOR HOLE COVER


    1. Install the rear door hole cover.

  16. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. Attach the 3 claws to install the rear door inside handle bezel plug.

  17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. Attach the 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  19. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here