LUGGAGE COMPARTMENT DOOR CLOSER SYSTEM Luggage Compartment Door Closer does not Operate

DESCRIPTION

The luggage compartment door closer is controlled by the luggage closer motor assembly. The closer motor is activated according to the switch signals in the luggage compartment door lock assembly.

WIRING DIAGRAM

Refer to the "System Diagram" Click here.

INSPECTION PROCEDURE

Note


  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. OPERATION INSPECTION


    1. Confirm the problem symptoms Click here.

      Result
      Result Proceed to
      The luggage compartment door does not operate properly. A
      The luggage compartment door does not operate properly when the luggage compartment door lock cylinder assembly is operated. B
      The luggage compartment door does not operate properly when the luggage electrical key switch is operated. C

    B

    READ VALUE USING GTS (TRUNK LOCK/UNLOCK SW) Click here

    C

    GO TO ENTRY AND START SYSTEM (for Entry Function)

    A

  2. READ VALUE USING GTS (PAWL POSITION SWITCH)


    1. Using the GTS, read the Data List Click here.

      Back Door
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Pawl Position Switch Luggage compartment door lock assembly pawl position switch signal / ON or OFF

      ON: Pawl position switch of luggage compartment door lock assembly on

      OFF: Pawl position switch of luggage compartment door lock assembly off (Luggage compartment door closed)

      • See "Luggage Compartment Door Closer Operation Timing Chart" Click here.

      • When this item is abnormal, there is a problem with the pawl position switch of the luggage compartment door lock assembly or related parts.
      OK
      On the screen, each item changes between ON and OFF as shown in above chart.

    NG

    CHECK HARNESS AND CONNECTOR (LUGGAGE CLOSER MOTOR - BATTERY AND BODY GROUND) Click here

    OK

    REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY Click here

  3. READ VALUE USING GTS (TRUNK LOCK/UNLOCK SW)


    1. Using the GTS, read the Data List Click here.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Trunk Lock/Unlock SW Luggage compartment door lock cylinder switch signal / ON or OFF

      ON: Luggage compartment door lock cylinder on (Luggage compartment door opened)

      OFF: Luggage compartment door lock cylinder off (Luggage compartment door closed)

      		 When this item is abnormal, there is a problem with the luggage compartment door lock cylinder switch or related parts.
      OK
      On the screen, each item changes between ON and OFF as shown in above chart.

    NG

    INSPECT LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY Click here

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

  4. CHECK HARNESS AND CONNECTOR (LUGGAGE CLOSER MOTOR - BATTERY AND BODY GROUND)


    1. A01FFLGE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Luggage Closer Motor Assembly)

      Disconnect the luggage closer motor connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U33-10 (ECUB) - Body ground Always 11 to 14 V
      U33-12 (B) - Body ground Always 11 to 14 V
      U33-8 (IG) - Body ground Engine switch on (IG) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U33-11 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    1. A01FE17E01
      Text in Illustration
      *a Full latch
      *b Half-latch
      *c Open latch

      Remove the luggage compartment door lock assembly Click here.

    2. Set the luggage compartment door lock assembly to the half-latch position.

    3. Apply battery voltage to the closer connector and check the closer operation.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 8 (M+)

      Battery negative (-) → Terminal 1 (M-)

      		 Luggage compartment door lock half-latch → full latch

    4. Set the luggage compartment door lock assembly to the full latch position.

    5. Apply battery voltage to the closer connector and check the open operation.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 1 (M-)

      Battery negative (-) → Terminal 8 (M+)

      		 Luggage compartment door lock full latch → open latch

    NG

    REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (LUGGAGE CLOSER MOTOR - LUGGAGE COMPARTMENT DOOR LOCK)


    1. Disconnect the U33 luggage closer motor connector.

    2. Disconnect the a9 luggage compartment door lock connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U33-2 (LCM+) - a9-8 (M+) Always Below 1 Ω
      U33-1 (LCM-) - a9-1 (M-) Always Below 1 Ω
      U33-20 (PAWL) - a9-11 (CLS) Always Below 1 Ω
      U33-16 (CSG) - a9-4 (CPSE) Always Below 1 Ω
      U33-17 (CS2) - a9-9 (CPS2) Always Below 1 Ω
      U33-18 (CS1) - a9-2 (CPS1) Always Below 1 Ω
      U33-19 (CSV) - a9-3 (CPS+) Always Below 1 Ω
      U33-7 (HAF) - a9-6 (FSW) Always Below 1 Ω
      U33-21 (SWG) - a9-7 (E) Always Below 1 Ω
      U33-21 (SWG) - a9-12 (CSWE) Always Below 1 Ω
      U33-2 (LCM+) - Body ground Always 10 kΩ or higher
      U33-1 (LCM-) - Body ground Always 10 kΩ or higher
      U33-20 (PAWL) - Body ground Always 10 kΩ or higher
      U33-16 (CSG) - Body ground Always 10 kΩ or higher
      U33-17 (CS2) - Body ground Always 10 kΩ or higher
      U33-18 (CS1) - Body ground Always 10 kΩ or higher
      U33-19 (CSV) - Body ground Always 10 kΩ or higher
      U33-7 (HAF) - Body ground Always 10 kΩ or higher
      U33-21 (SWG) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    1. Temporarily replace the luggage compartment door lock with a new or normally functioning one Click here.

    2. Check the luggage compartment door closer operation.

      OK
      Luggage compartment door closer normal operation.

    NG

    REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY Click here

    OK

    END (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY WAS DEFECTIVE)

  8. INSPECT LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY


    1. A01FDLJ

      Remove the luggage compartment door lock cylinder Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - 2 Not turned 10 kΩ or higher
      1 - 2 Open position Below 1 Ω

    NG

    REPLACE LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - LUGGAGE COMPARTMENT DOOR LOCK CYLINDER AND BODY GROUND)


    1. Disconnect the N12 main body ECU connector.

    2. Disconnect the a4 luggage compartment door lock cylinder connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N12-23 (TKUL) - a4-2 Always Below 1 Ω
      a4-1 - Body ground Always Below 1 Ω
      N12-23 (TKUL) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here