FRONT SEAT ASSEMBLY (for Standard Seat Type) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE SEAT ADJUSTER COVER CAP LH

    A01FF33

    1. Remove the 2 seat adjuster cover caps.

  2. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD LH

    A01FG26

    1. Remove the screw.

    2. Detach the 2 claws and 2 clips and remove the front seat inner No. 1 cushion shield LH.

  3. REMOVE FRONT SEAT CUSHION SHIELD LH

    A01FDJ8E01
    Text in Illustration
    *1 Hook
    *2 Guide

    1. Remove the 2 screws.

    2. Detach the 3 claws and 2 guides.

    3. Detach the hook and remove the front seat cushion shield LH.

  4. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

    A01FH8DE01
    Text in Illustration
    *1 Hook
    *2 Guide

    1. Remove the screw.

    2. Detach the 3 claws and 3 guides.

    3. Detach the hook and remove the front seat inner cushion shield LH.

  5. REMOVE POWER SEAT SWITCH KNOB LH (for Slide)

    A01FDQTE01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Using moulding remover A, detach the 4 claws and remove the power seat switch knob LH.

  6. REMOVE POWER SEAT SWITCH KNOB LH (for Reclining)

    A01FI41E01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Using moulding remover A, detach the 3 claws and remove the power seat switch knob LH.

  7. REMOVE FRONT POWER ADJUSTER SHIELD LH

    A01FGVQ

    1. Remove the 2 screws.

    2. Detach the 2 clips and remove the front power adjuster shield LH.

    3. A01FGNH

      for Driver Side:

      Disconnect the 3 connectors.

    4. A01FHW5

      for Front Passenger Side:

      Disconnect the 2 connectors.

    5. A01FFPY

      Remove the 4 screws and switch bezel from the front power adjuster shield LH.

    6. A01FFN0

      Remove the 2 clips from the front power adjuster shield LH.

  8. REMOVE POWER SEAT SWITCH ASSEMBLY

    A01FDMI

    1. Remove the 3 screws and 3 nuts.

    2. Detach the 2 claws and remove the power seat switch assembly from the switch bezel.

  9. REMOVE FRONT LUMBAR POWER SEAT SWITCH

    A01FEMYE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the front lumbar power seat switch.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE UPPER SEAT TRACK RAIL COVER LH

    A01FGRV

    1. Remove the screw.

    2. Detach the clip and remove the upper seat track rail cover LH.

  11. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)


    1. A01FHEM

      Disconnect the connector from the seat position airbag sensor.

    2. Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position airbag sensor.

  12. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. Disconnect each connector and each clamp.

    2. A01FG2V

      Remove the nut and front seat inner belt assembly LH.

  13. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01FGBV

    1. Using a clip remover, remove the clip and disconnect the rubber band.

    2. Detach the hook and disconnect the rubber band.

    3. Using a clip remover, remove the clip.

    4. A01FH5P

      Open the lower part of the front seatback board sub-assembly LH and remove the 2 screws.

    5. Push and slide the front seatback board subassembly LH to detach the claw.

      Tech Tips

      Use the same procedure to detach the claw on the other side.

    6. Slide the front seatback board sub-assembly LH downward to detach the 2 hooks and remove it.

  14. REMOVE FRONT SEAT LEG COVER LH

    A01FDF3

    1. Remove the 2 screws.

    2. Detach the clip and remove the front seat leg cover LH.

  15. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH

    A01FHZG

    1. Remove the 2 screws.

    2. Detach the clip and remove the front seat lower cushion shield LH.

  16. REMOVE SEAT CUSHION COVER WITH PAD


    1. w/ Seat Heater System:


      1. A01FIM5E01
        Text in Illustration
        *1 Connector Lock

        Disconnect the 2 connectors.

      2. Remove the connector lock from the seat heater control sub-assembly LH connector and disconnect the connector.

    2. Using a clip remover, remove the 4 clips.

      A01FDI3
    3. A01FG62

      for Front Passenger Side:

      Disconnect the connector.

    4. Detach the hooks and remove the seat cushion cover with pad.

  17. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01FHNYE01
      Text in Illustration
      *1 Strap

      Remove the hog rings and disconnect the 3 straps from the separate type front seat cushion pad.

    2. A01FILR

      Remove the hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.

  18. REMOVE SEAT CUSHION SPRING DAMPER

    A01FEBP

    1. Remove the 2 nuts and seat cushion spring damper.

  19. REMOVE SEATBACK COVER WITH PAD

    A01FDR9

    1. Detach the hooks.

    2. A01FIPY

      Detach the 4 claws and remove the 2 front seat headrest supports.

    3. A01FHN4E01

      Detach the wire harness clamp.

    4. Remove the 2 nuts and detach the 2 seatback cover brackets.

      Text in Illustration
      *1 Seatback Cover Bracket

    5. Remove the seatback cover with pad.

  20. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. A01FG8P

      Pass the 2 seatback cover brackets through the 2 holes of the separate type front seatback pad.

    2. A01FILX

      Remove the hog rings and separate type front seatback cover from the separate type front seatback pad.

  21. REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY


    1. A01FGSO

      Remove the screw and No. 1 interior illumination light assembly.

    2. Disconnect the connector.

  22. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

    A01FDDL

    1. Disconnect the connector.

    2. Detach the 2 claws and disconnect the rear air duct LH from the lumbar support adjuster assembly LH.

    3. Remove the 2 screws.

    4. Detach the hook and remove the seatback climate control blower LH together with the rear air duct LH.

  23. REMOVE REAR AIR DUCT LH (w/ Climate Control Seat System)

    A01FG7L

    1. Detach the 2 claws and remove the rear air duct LH from the seatback climate control blower LH.

  24. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    A01FIUH

    1. Disconnect the connector.

    2. Remove the 2 springs and detach the 2 clips.

    3. A01FG0G

      Remove the 2 bolts.

    4. Slide the lumbar support adjuster assembly LH upward to detach the 2 hooks and remove it.

  25. REMOVE FRONT SEATBACK INSIDE SPRING SET PLATE LH

    A01FDS9

    1. Remove the front seatback inside spring set plate LH from the front seat bracket LH.

  26. REMOVE FRONT SEAT BRACKET LH

    A01FH1Y

    1. Remove the nut and front seat bracket LH.

  27. REMOVE FRONT SEATBACK INSIDE SPRING SET PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE FRONT SEAT BRACKET RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH


    1. A01FDXUE01
      Text in Illustration
      *1 Housing Lock
      *2 Outer Housing

      Disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push the housing lock and slide the outer housing. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

    2. Detach the connector clamp from the front seatback frame sub-assembly.

    3. Remove the 2 nuts and the front seat airbag assembly.

      CAUTION:


      • The nuts must not be reused.

      • Make sure that the front seatback frame sub-assembly is not deformed. If it is, replace it with a new one.

  30. REMOVE POWER SEAT MOTOR ASSEMBLY


    1. A01FH0J

      Disconnect the connector.

    2. A01FEAP

      Detach the 5 claws and remove the push nut from the reclining connecting pipe.

    3. A01FEAV

      Remove the reclining connecting pipe.

    4. Remove the bolt and power seat motor assembly.

  31. REMOVE RECLINING ADJUSTER INSIDE COVER

    A01FIX4

    1. Remove the reclining adjuster inside cover.

  32. REMOVE FRONT NO. 1 SEATBACK WIRE SET BRACKET

    A01FIXY

    1. Remove the nut and front No. 1 seatback wire set bracket.

  33. REMOVE FRONT NO. 2 SEATBACK WIRE SET BRACKET

    A01FIHU

    1. Remove the nut and front No. 2 seatback wire set bracket.

  34. REMOVE RECLINING ADJUSTER INSIDE COVER LH

    A01FFAOE01
    Text in Illustration
    *1 Guide
    *2 Hook

    1. Remove the screw and detach the guide.

    2. Detach the 2 hooks and remove the reclining adjuster inside cover LH.

  35. REMOVE RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

    A01FFS0

    1. Detach the claw and remove the seat heater control sub-assembly LH.

  37. REMOVE SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

    A01FFK7

    1. Disconnect the connector.

    2. Remove the 2 screws.

    3. A01FIRSE01
      Text in Illustration
      *1 Tab

      Open the 2 tabs as shown in the illustration.

    4. Detach the 2 hooks and remove the seat climate control blower LH together with the seat cushion climate control duct LH from the separate type front seat cushion spring assembly.

  38. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)

    A01FGH7

    1. Detach the 2 claws and remove the seat cushion climate control duct LH from the seat climate control blower LH.

  39. REMOVE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    A01FHZ9E01
    Text in Illustration
    *1 Wire Harness Clamp
    *2 Hook A
    *3 Hook B

    1. Detach the 3 wire harness clamps.

    2. Detach the 4 hooks A.

    3. Detach the 4 hooks B and remove the separate type front seat cushion spring assembly.

  40. REMOVE FRONT SEAT WIRE

    A01FDSZ

    1. Detach the 4 wire harness clamps.

    2. A01FGSH

      Disconnect the 3 connectors.

    3. Detach the 9 wire harness clamps and remove the front seat wire.

  41. REMOVE SEATBACK FELT

    A01FEH7

    1. Remove the seatback felt.

  42. REMOVE FRONT SEATBACK FRAME SUB-ASSEMBLY LH

    A01FJ25

    1. Remove the 4 bolts and front seatback frame sub-assembly LH from the front seat adjuster LH.