FRONT SEAT ASSEMBLY (for Luxury Seat Type) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE SEAT ADJUSTER COVER CAP LH

    A01FF33

    1. Remove the 2 seat adjuster cover caps.

  2. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD LH

    A01FDCH

    1. Remove the screw.

    2. Detach the 2 claws and 2 clips and remove the front seat inner No. 1 cushion shield LH.

  3. REMOVE FRONT SEAT CUSHION SHIELD LH

    A01FDJ8E01
    Text in Illustration
    *1 Hook
    *2 Guide

    1. Remove the 2 screws.

    2. Detach the 3 claws and 2 guides.

    3. Detach the hook and remove the front seat cushion shield LH.

  4. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

    A01FH8DE01
    Text in Illustration
    *1 Hook
    *2 Guide

    1. Remove the screw.

    2. Detach the 3 claws and 3 guides.

    3. Detach the hook and remove the front seat inner cushion shield LH.

  5. REMOVE POWER SEAT SWITCH KNOB LH (for Slide)

    A01FDQTE01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Using moulding remover A, detach the 4 claws and remove the power seat switch knob LH.

  6. REMOVE POWER SEAT SWITCH KNOB LH (for Reclining)

    A01FI41E01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Using moulding remover A, detach the 3 claws and remove the power seat switch knob LH.

  7. REMOVE FRONT POWER ADJUSTER SHIELD LH

    A01FGVQ

    1. Remove the 2 screws.

    2. Detach the 2 clips and remove the front power adjuster shield LH.

    3. A01FF9V

      Disconnect the connector.

    4. A01FGD2

      Remove the 4 screws and switch bezel from the front power adjuster shield LH.

    5. A01FFN0

      Remove the 2 clips from the front power adjuster shield LH.

  8. REMOVE POWER SEAT SWITCH ASSEMBLY

    A01FDMI

    1. Remove the 3 screws and 3 nuts.

    2. Detach the 2 claws and remove the power seat switch assembly from the switch bezel.

  9. REMOVE UPPER SEAT TRACK RAIL COVER LH

    A01FGRV

    1. Remove the screw.

    2. Detach the clip and remove the upper seat track rail cover LH.

  10. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)


    1. A01FHEM

      Disconnect the connector from the seat position airbag sensor.

    2. Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position airbag sensor.

  11. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. Disconnect each connector and each clamp.

    2. A01FG2V

      Remove the nut and front seat inner belt assembly LH.

  12. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01FEPU

    1. Using a clip remover, remove the clip and disconnect the rubber band.

    2. Detach the hook and disconnect the rubber band.

    3. Using a clip remover, remove the clip.

    4. A01FG40

      Open the lower part of the front seatback board sub-assembly LH and remove the 2 screws.

    5. Push and slide the front seatback board subassembly LH to detach the claw.

      Tech Tips

      Use the same procedure to detach the claw on the other side.

    6. Slide the front seatback board sub-assembly LH downward to detach the 2 hooks and remove it.

  13. REMOVE FRONT SEATBACK BOARD

    A01FDEF

    1. Remove the 2 screws.

    2. Slide the front seatback board downward to detach the 2 hooks and remove it.

  14. REMOVE FRONT SEAT LEG COVER LH

    A01FDF3

    1. Remove the 2 screws.

    2. Detach the clip and remove the front seat leg cover LH.

  15. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH

    A01FHZG

    1. Remove the 2 screws.

    2. Detach the clip and remove the front seat lower cushion shield LH.

  16. REMOVE SEAT CUSHION COVER WITH PAD

    A01FF8ZE03
    Text in Illustration
    *A except Ottoman - -
    *1 Connector Lock - -

    1. Disconnect the 2 connectors.

    2. Remove the connector lock from the seat heater control sub-assembly LH connector and disconnect the connector.

    3. Using a clip remover, remove the 4 clips.

    4. A01FG62

      for Front Passenger Side:

      Disconnect the connector.

    5. except Ottoman:

      Using a clip remover, remove the 2 clips and open the front part of the separate type front seat cushion cover.

    6. A01FHYV

      Remove the hog rings.

    7. Using a clip remover, detach the 4 clips and disconnect the front part of the separate type front seat cushion cover.

    8. Detach the hooks and remove the seat cushion cover with pad.

  17. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (except Ottoman)


    1. A01FHNYE01
      Text in Illustration
      *1 Strap

      Remove the hog rings and disconnect the 3 straps from the separate type front seat cushion pad.

    2. A01FEHO

      Remove the hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.

  18. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (for Ottoman)


    1. A01FILHE01
      Text in Illustration
      *1 Strap

      Remove the hog rings and disconnect the 3 straps from the separate type front seat cushion pad.

    2. A01FD8P

      Remove the hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.

  19. REMOVE SEAT CUSHION SPRING DAMPER

    A01FEBP

    1. Remove the 2 nuts and seat cushion spring damper.

  20. REMOVE FRONT POWER SEAT SWITCH ASSEMBLY RH (w/ Shoulder Switch)


    1. A01FGXM

      Detach the wire harness clamp.

    2. A01FG82E01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape as shown in the illustration.

    3. Using moulding remover A, detach the 2 claws and remove the front power seat switch assembly RH.

    4. A01FD8U

      Disconnect the connector.

  21. REMOVE SEATBACK COVER WITH PAD

    A01FHC0

    1. Detach the hooks.

    2. A01FF3R

      Detach the wire harness clamp.

    3. A01FDBI

      Detach the 4 claws and remove the 2 front seat headrest supports.

    4. A01FGINE01

      Detach the wire harness clamp.

    5. Remove the 2 nuts and detach the seatback cover bracket.

      Text in Illustration
      *1 Seatback Cover Bracket
    6. Remove the seatback cover with pad.

  22. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. A01FHOJ

      Remove the hog rings and separate type front seatback cover from the separate type front seatback pad.

  23. REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY


    1. A01FGSO

      Remove the screw and No. 1 interior illumination light assembly.

    2. Disconnect the connector.

  24. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH

    A01FGEY

    1. Disconnect the connector.

    2. Detach the 2 claws and disconnect the rear air duct LH from the lumbar support adjuster assembly LH.

    3. Remove the 2 screws.

    4. Detach the hook and remove the seatback climate control blower LH together with the rear air duct LH.

  25. REMOVE REAR AIR DUCT LH

    A01FG7L

    1. Detach the 2 claws and remove the rear air duct LH from the seatback climate control blower LH.

  26. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. A01FIPI

      Disconnect the 2 connectors.

    2. Detach the 2 cable clamps.

    3. A01FHAO

      Remove the 2 springs and detach the 2 clips.

    4. A01FG0G

      Remove the 2 bolts.

    5. Slide the lumbar support adjuster assembly LH upward to detach the 2 hooks and remove it.

  27. REMOVE FRONT SEATBACK ADJUSTER ASSEMBLY

    A01FFBO

    1. Disconnect the connector.

    2. Remove the 4 bolts and the left and right ends of the front seatback adjuster assembly.

      Note

      Make sure that the left and right ends of the front seatback adjuster assembly do not become detached from the motor.

    3. Remove the 2 bolts.

    4. Slide the front seatback adjuster to detach the guide as shown in the illustration and remove it.

      Text in Illustration
      A01FJ4N Slide
  28. REMOVE FRONT SEATBACK SUPPORT LH

    A01FFEME01

    1. Disconnect the connector.

    2. Remove the 4 nuts and both paddles of the front seatback support LH.

      Text in Illustration
      *1 Paddle
    3. A01FFJZ

      Remove the nut and front seatback support LH.

  29. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH


    1. A01FDXUE01
      Text in Illustration
      *1 Housing Lock
      *2 Outer Housing

      Disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push the housing lock and slide the outer housing. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

    2. Detach the connector clamp from the front seatback frame sub-assembly.

    3. Remove the 2 nuts and the front seat airbag assembly.

      CAUTION:


      • The nuts must not be reused.

      • Make sure that the front seatback frame sub-assembly is not deformed. If it is, replace it with a new one.

  30. REMOVE INNER SEAT BRACKET ASSEMBLY LH

    A01FF16

    1. Remove the 2 nuts and inner seat bracket assembly LH.

  31. REMOVE POWER SEAT MOTOR ASSEMBLY

    A01FH0J

    1. Disconnect the connector.

    2. A01FEAP

      Detach the 5 claws and remove the push nut from the reclining connecting pipe.

    3. A01FEAV

      Remove the reclining connecting pipe.

    4. Remove the bolt and power seat motor assembly.

  32. REMOVE RECLINING ADJUSTER INSIDE COVER

    A01FIX4

    1. Remove the reclining adjuster inside cover.

  33. REMOVE POSITION CONTROL ECU ASSEMBLY


    1. A01FDFOE01
      Text in Illustration
      *1 Wire Harness Clamp
      *2 Clamp

      Disconnect the connector and detach the wire harness clamp.

    2. Detach the 2 clamps and move the front seat wire connector housing.

    3. Disconnect the 4 connectors.

    4. A01FDPR

      Remove the 3 bolts and position control ECU assembly.

  34. REMOVE RECLINING ADJUSTER INSIDE COVER LH

    A01FFAOE01
    Text in Illustration
    *1 Guide
    *2 Hook

    1. Remove the screw and detach the guide.

    2. Detach the 2 hooks and remove the reclining adjuster inside cover LH.

  35. REMOVE RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH

    A01FFS0

    1. Detach the claw and remove the seat heater control sub-assembly LH.

  37. REMOVE SEAT CLIMATE CONTROL BLOWER LH

    A01FFK7

    1. Disconnect the connector.

    2. Remove the 2 screws.

    3. A01FIRSE01
      Text in Illustration
      *1 Tab

      Open the 2 tabs as shown in the illustration.

    4. Detach the 2 hooks and remove the seat climate control blower LH together with the seat cushion climate control duct LH from the separate type front seat cushion spring assembly.

  38. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH

    A01FGH7

    1. Detach the 2 claws and remove the seat cushion climate control duct LH from the seat climate control blower LH.

  39. REMOVE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    A01FF2WE02
    Text in Illustration
    *1 Wire Harness Clamp
    *2 Hook A
    *3 Hook B

    1. Detach the 4 wire harness clamps.

    2. Detach the 4 hooks A.

    3. Detach the 4 hooks B and remove the separate type front seat cushion spring assembly.

  40. REMOVE FRONT SEAT WIRE


    1. A01FFRN

      Detach the 7 wire harness clamps.

    2. A01FH2T

      Disconnect the 3 connectors.

    3. Remove the nut and disconnect the ground wire.

    4. Detach the 8 wire harness clamps and remove the front seat wire.

  41. REMOVE SEATBACK SPRING DAMPER LH

    A01FEAG

    1. Remove the 2 nuts and seatback spring damper LH.

  42. REMOVE FRONT SEATBACK FRAME SUB-ASSEMBLY LH

    A01FGT9

    1. Remove the 4 bolts and front seatback frame sub-assembly LH from the front seat adjuster LH.